******** Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 911076 Date: 101209

3G MMI(R) - Satellite Radio Concerns

91 3G MMI: Satellite radio concerns

91 10 76

2024200/2

December 9, 2010.

Supersedes Technical Service Bulletin Group 91 number 10-51 dated August 18, 2010 for reasons listed below.

Affected Vehicles

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 431

Condition

^ Satellite radio band selection is not available using the Radio selection button in the 3G MMI control panel.

^ Satellite radio pre-set stations intermittently disappear.

Technical Background

Software issue in the radio.

Production Solution

New software (ZUG 0114).

Service

Tip: For successful results, the steps must be performed in this sequence.

1. Check 3G MMI system software version

2. Update software of the 3G MMI system

3. Perform feedback documentation to the SVM

1. Check 3G MMI system software version

1. Switch on ignition and wait approximately 1 minute.

2. Press the SETUP and RETURN buttons simultaneously and hold both buttons down for about 5 seconds.

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 432

If this message is displayed, the system is not yet completely initialized. Wait a few seconds, then press the RETURN button.

3. Read current MMI train (Zug) version.

4. The train (Zug) versions listed in the table below must be updated.

P versions are production build.

K versions are service updates.

2. Update software of the 3G MMI system

1. Connect an approved Audi battery maintainer/charger to vehicle.

2. Switch off all unnecessary electrical equipment (blower, seat heater, interior light, etc.).

Tip: Also make sure that no electromagnetic interference sources (mobile phone) are operated in or near the vehicle while individual control units

are being updated.

Tip: For complete and detailed instructions for the 3G MMI system update, refer to the attached instructions. (Note: The attached instructions are

generic. Some portions may not apply to this specific TSB. Importing and exporting customer code data is not necessary for this 3G MMI update

system.)

3. Insert update CD into the 3G MMI main (head) drive unit located in the center of the instrument panel.

4. Start the software update.

5. After the software update has been performed, confirm the "Abort (cancel) documentation" selection. The 3G MMI system will restart. Then

perform the feedback documentation.

3. Perform feedback documentation to the SVM

1. Follow all instructions in the attached TSB 2011732 00 Software Version Management (SVM), operating instructions.

2. Confirm any proposed parameter settings and codings.

3. Then perform test program "5F - Information electronics, resetting fault memory" to clear any faults in the system.

Tip: No control unit is flashed as part of the feedback documentation to the SVM. Do not perform any updates of control units. Do not replace any

control units.

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 433

Warranty

Required Parts and Tools

Additional information

The following Technical Service Bulletin will be necessary to complete this procedure:

^ TSB 2011732 00 Software Version Management (SVM), operating instructions.

All part and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Dept. and service manuals

for the latest information.

Attachment

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 434

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 435

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 436

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 437

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 438

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 439

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 440

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 441

2011732 00 Software Version Management (SVM), operating instructions

Instructions For MMI 3G Nav. Plus Update

Instructions for MMI 3G Nav. Plus update

MMI update programming for vehicles equipped with MMI 3G, e.g. the Audi Q5 (8R) with feedback documentation via Software Versions

Management (Audi SVM).

Overview of the MMI 3G Systems described here with relevant PR no.:

MMI 3G - 8DY

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 442

1. Overview of controls

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 443

2. Important information about update programming

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 444

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 445

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 446

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 447

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 448

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 449

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 450

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 451

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 452

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 453

3. Carrying out update programming

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 454

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 455

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 456

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 457

4. Changing languages, only for MMI 3G Radio/Basic Plus systems (not available in Audi Q5 models).

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 458

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 459

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 460

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 461

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 462

5. Importing and exporting customer data (MMI 3G Navigation Plus)

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 463

Activating imported customer data.

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 464

******** Audi A4 Quattro Wagon (8K5) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 911076 Date: 101209

3G MMI(R) - Satellite Radio Concerns

91 3G MMI: Satellite radio concerns

91 10 76

2024200/2

December 9, 2010.

Supersedes Technical Service Bulletin Group 91 number 10-51 dated August 18, 2010 for reasons listed below.

Affected Vehicles

437

Condition

^ Satellite radio band selection is not available using the Radio selection button in the 3G MMI control panel.

^ Satellite radio pre-set stations intermittently disappear.

Technical Background

Software issue in the radio.

Production Solution

New software (ZUG 0114).

Service

Tip: For successful results, the steps must be performed in this sequence.

1. Check 3G MMI system software version

2. Update software of the 3G MMI system

3. Perform feedback documentation to the SVM

1. Check 3G MMI system software version

1. Switch on ignition and wait approximately 1 minute.

2. Press the SETUP and RETURN buttons simultaneously and hold both buttons down for about 5 seconds.

438

If this message is displayed, the system is not yet completely initialized. Wait a few seconds, then press the RETURN button.

3. Read current MMI train (Zug) version.

4. The train (Zug) versions listed in the table below must be updated.

P versions are production build.

K versions are service updates.

2. Update software of the 3G MMI system

1. Connect an approved Audi battery maintainer/charger to vehicle.

2. Switch off all unnecessary electrical equipment (blower, seat heater, interior light, etc.).

Tip: Also make sure that no electromagnetic interference sources (mobile phone) are operated in or near the vehicle while individual control units

are being updated.

Tip: For complete and detailed instructions for the 3G MMI system update, refer to the attached instructions. (Note: The attached instructions are

generic. Some portions may not apply to this specific TSB. Importing and exporting customer code data is not necessary for this 3G MMI update

system.)

3. Insert update CD into the 3G MMI main (head) drive unit located in the center of the instrument panel.

4. Start the software update.

5. After the software update has been performed, confirm the "Abort (cancel) documentation" selection. The 3G MMI system will restart. Then

perform the feedback documentation.

3. Perform feedback documentation to the SVM

1. Follow all instructions in the attached TSB 2011732 00 Software Version Management (SVM), operating instructions.

2. Confirm any proposed parameter settings and codings.

3. Then perform test program "5F - Information electronics, resetting fault memory" to clear any faults in the system.

Tip: No control unit is flashed as part of the feedback documentation to the SVM. Do not perform any updates of control units. Do not replace any

control units.

439

Warranty

Required Parts and Tools

Additional information

The following Technical Service Bulletin will be necessary to complete this procedure:

^ TSB 2011732 00 Software Version Management (SVM), operating instructions.

All part and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Dept. and service manuals

for the latest information.

Attachment

440

441

442

443

444

445

446

447

2011732 00 Software Version Management (SVM), operating instructions

Instructions For MMI 3G Nav. Plus Update

Instructions for MMI 3G Nav. Plus update

MMI update programming for vehicles equipped with MMI 3G, e.g. the Audi Q5 (8R) with feedback documentation via Software Versions

Management (Audi SVM).

Overview of the MMI 3G Systems described here with relevant PR no.:

MMI 3G - 8DY

448

1. Overview of controls

449

2. Important information about update programming

450

451

452

453

454

455

456

457

458

459

3. Carrying out update programming

460

461

462

463

4. Changing languages, only for MMI 3G Radio/Basic Plus systems (not available in Audi Q5 models).

464

465

466

467

468

5. Importing and exporting customer data (MMI 3G Navigation Plus)

469

Activating imported customer data.

******** Audi A4 Sedan (8K2) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 911076 Date: 101209

3G MMI(R) - Satellite Radio Concerns

91 3G MMI: Satellite radio concerns

91 10 76

2024200/2

December 9, 2010.

Supersedes Technical Service Bulletin Group 91 number 10-51 dated August 18, 2010 for reasons listed below.

Affected Vehicles

431

Condition

^ Satellite radio band selection is not available using the Radio selection button in the 3G MMI control panel.

^ Satellite radio pre-set stations intermittently disappear.

Technical Background

Software issue in the radio.

Production Solution

New software (ZUG 0114).

Service

Tip: For successful results, the steps must be performed in this sequence.

1. Check 3G MMI system software version

2. Update software of the 3G MMI system

3. Perform feedback documentation to the SVM

1. Check 3G MMI system software version

1. Switch on ignition and wait approximately 1 minute.

2. Press the SETUP and RETURN buttons simultaneously and hold both buttons down for about 5 seconds.

432

If this message is displayed, the system is not yet completely initialized. Wait a few seconds, then press the RETURN button.

3. Read current MMI train (Zug) version.

4. The train (Zug) versions listed in the table below must be updated.

P versions are production build.

K versions are service updates.

2. Update software of the 3G MMI system

1. Connect an approved Audi battery maintainer/charger to vehicle.

2. Switch off all unnecessary electrical equipment (blower, seat heater, interior light, etc.).

Tip: Also make sure that no electromagnetic interference sources (mobile phone) are operated in or near the vehicle while individual control units

are being updated.

Tip: For complete and detailed instructions for the 3G MMI system update, refer to the attached instructions. (Note: The attached instructions are

generic. Some portions may not apply to this specific TSB. Importing and exporting customer code data is not necessary for this 3G MMI update

system.)

3. Insert update CD into the 3G MMI main (head) drive unit located in the center of the instrument panel.

4. Start the software update.

5. After the software update has been performed, confirm the "Abort (cancel) documentation" selection. The 3G MMI system will restart. Then

perform the feedback documentation.

3. Perform feedback documentation to the SVM

1. Follow all instructions in the attached TSB 2011732 00 Software Version Management (SVM), operating instructions.

2. Confirm any proposed parameter settings and codings.

3. Then perform test program "5F - Information electronics, resetting fault memory" to clear any faults in the system.

Tip: No control unit is flashed as part of the feedback documentation to the SVM. Do not perform any updates of control units. Do not replace any

control units.

433

Warranty

Required Parts and Tools

Additional information

The following Technical Service Bulletin will be necessary to complete this procedure:

^ TSB 2011732 00 Software Version Management (SVM), operating instructions.

All part and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Dept. and service manuals

for the latest information.

Attachment

434

435

436

437

438

439

440

441

2011732 00 Software Version Management (SVM), operating instructions

Instructions For MMI 3G Nav. Plus Update

Instructions for MMI 3G Nav. Plus update

MMI update programming for vehicles equipped with MMI 3G, e.g. the Audi Q5 (8R) with feedback documentation via Software Versions

Management (Audi SVM).

Overview of the MMI 3G Systems described here with relevant PR no.:

MMI 3G - 8DY

442

1. Overview of controls

443

2. Important information about update programming

444

445

446

447

448

449

450

451

452

453

3. Carrying out update programming

454

455

456

457

4. Changing languages, only for MMI 3G Radio/Basic Plus systems (not available in Audi Q5 models).

458

459

460

461

462

5. Importing and exporting customer data (MMI 3G Navigation Plus)

463

Activating imported customer data.

******** Audi A5 Cabriolet (8F7) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 911076 Date: 101209

3G MMI(R) - Satellite Radio Concerns

91 3G MMI: Satellite radio concerns

91 10 76

2024200/2

December 9, 2010.

Supersedes Technical Service Bulletin Group 91 number 10-51 dated August 18, 2010 for reasons listed below.

Affected Vehicles

405

Condition

^ Satellite radio band selection is not available using the Radio selection button in the 3G MMI control panel.

^ Satellite radio pre-set stations intermittently disappear.

Technical Background

Software issue in the radio.

Production Solution

New software (ZUG 0114).

Service

Tip: For successful results, the steps must be performed in this sequence.

1. Check 3G MMI system software version

2. Update software of the 3G MMI system

3. Perform feedback documentation to the SVM

1. Check 3G MMI system software version

1. Switch on ignition and wait approximately 1 minute.

2. Press the SETUP and RETURN buttons simultaneously and hold both buttons down for about 5 seconds.

406

If this message is displayed, the system is not yet completely initialized. Wait a few seconds, then press the RETURN button.

3. Read current MMI train (Zug) version.

4. The train (Zug) versions listed in the table below must be updated.

P versions are production build.

K versions are service updates.

2. Update software of the 3G MMI system

1. Connect an approved Audi battery maintainer/charger to vehicle.

2. Switch off all unnecessary electrical equipment (blower, seat heater, interior light, etc.).

Tip: Also make sure that no electromagnetic interference sources (mobile phone) are operated in or near the vehicle while individual control units

are being updated.

Tip: For complete and detailed instructions for the 3G MMI system update, refer to the attached instructions. (Note: The attached instructions are

generic. Some portions may not apply to this specific TSB. Importing and exporting customer code data is not necessary for this 3G MMI update

system.)

3. Insert update CD into the 3G MMI main (head) drive unit located in the center of the instrument panel.

4. Start the software update.

5. After the software update has been performed, confirm the "Abort (cancel) documentation" selection. The 3G MMI system will restart. Then

perform the feedback documentation.

3. Perform feedback documentation to the SVM

1. Follow all instructions in the attached TSB 2011732 00 Software Version Management (SVM), operating instructions.

2. Confirm any proposed parameter settings and codings.

3. Then perform test program "5F - Information electronics, resetting fault memory" to clear any faults in the system.

Tip: No control unit is flashed as part of the feedback documentation to the SVM. Do not perform any updates of control units. Do not replace any

control units.

407

Warranty

Required Parts and Tools

Additional information

The following Technical Service Bulletin will be necessary to complete this procedure:

^ TSB 2011732 00 Software Version Management (SVM), operating instructions.

All part and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Dept. and service manuals

for the latest information.

Attachment

408

409

410

411

412

413

414

415

2011732 00 Software Version Management (SVM), operating instructions

Instructions For MMI 3G Nav. Plus Update

Instructions for MMI 3G Nav. Plus update

MMI update programming for vehicles equipped with MMI 3G, e.g. the Audi Q5 (8R) with feedback documentation via Software Versions

Management (Audi SVM).

Overview of the MMI 3G Systems described here with relevant PR no.:

MMI 3G - 8DY

416

1. Overview of controls

417

2. Important information about update programming

418

419

420

421

422

423

424

425

426

427

3. Carrying out update programming

428

429

430

431

4. Changing languages, only for MMI 3G Radio/Basic Plus systems (not available in Audi Q5 models).

432

433

434

435

436

5. Importing and exporting customer data (MMI 3G Navigation Plus)

437

Activating imported customer data.

******** Audi A6 Quattro Sedan (4F2) V6-3.0L SC (CCAA) Technical Service Bulletin # 911076 Date: 101209

3G MMI(R) - Satellite Radio Concerns

91 3G MMI: Satellite radio concerns

91 10 76

2024200/2

December 9, 2010.

Supersedes Technical Service Bulletin Group 91 number 10-51 dated August 18, 2010 for reasons listed below.

Affected Vehicles

Condition

^ Satellite radio band selection is not available using the Radio selection button in the 3G MMI control panel.

^ Satellite radio pre-set stations intermittently disappear.

Technical Background

Software issue in the radio.

Production Solution

New software (ZUG 0114).

Service

Tip: For successful results, the steps must be performed in this sequence.

1. Check 3G MMI system software version

2. Update software of the 3G MMI system

3. Perform feedback documentation to the SVM

1. Check 3G MMI system software version

1. Switch on ignition and wait approximately 1 minute.

302

2. Press the SETUP and RETURN buttons simultaneously and hold both buttons down for about 5 seconds.

If this message is displayed, the system is not yet completely initialized. Wait a few seconds, then press the RETURN button.

3. Read current MMI train (Zug) version.

4. The train (Zug) versions listed in the table below must be updated.

P versions are production build.

K versions are service updates.

2. Update software of the 3G MMI system

1. Connect an approved Audi battery maintainer/charger to vehicle.

2. Switch off all unnecessary electrical equipment (blower, seat heater, interior light, etc.).

Tip: Also make sure that no electromagnetic interference sources (mobile phone) are operated in or near the vehicle while individual control units

are being updated.

303

Tip: For complete and detailed instructions for the 3G MMI system update, refer to the attached instructions. (Note: The attached instructions are

generic. Some portions may not apply to this specific TSB. Importing and exporting customer code data is not necessary for this 3G MMI update

system.)

3. Insert update CD into the 3G MMI main (head) drive unit located in the center of the instrument panel.

4. Start the software update.

5. After the software update has been performed, confirm the "Abort (cancel) documentation" selection. The 3G MMI system will restart. Then

perform the feedback documentation.

3. Perform feedback documentation to the SVM

1. Follow all instructions in the attached TSB 2011732 00 Software Version Management (SVM), operating instructions.

2. Confirm any proposed parameter settings and codings.

3. Then perform test program "5F - Information electronics, resetting fault memory" to clear any faults in the system.

Tip: No control unit is flashed as part of the feedback documentation to the SVM. Do not perform any updates of control units. Do not replace any

control units.

Warranty

304

Required Parts and Tools

Additional information

The following Technical Service Bulletin will be necessary to complete this procedure:

^ TSB 2011732 00 Software Version Management (SVM), operating instructions.

All part and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Dept. and service manuals

for the latest information.

Attachment

305

306

307

308

309

310

311

312

2011732 00 Software Version Management (SVM), operating instructions

Instructions For MMI 3G Nav. Plus Update

Instructions for MMI 3G Nav. Plus update

MMI update programming for vehicles equipped with MMI 3G, e.g. the Audi Q5 (8R) with feedback documentation via Software Versions

Management (Audi SVM).

Overview of the MMI 3G Systems described here with relevant PR no.:

MMI 3G - 8DY

313

1. Overview of controls

314

2. Important information about update programming

315

316

317

318

319

320

321

322

323

324

3. Carrying out update programming

325

326

327

328

4. Changing languages, only for MMI 3G Radio/Basic Plus systems (not available in Audi Q5 models).

329

330

331

332

333

5. Importing and exporting customer data (MMI 3G Navigation Plus)

334

Activating imported customer data.

******** Audi A6 Sedan (4F2) V6-3.2L (CALA) Technical Service Bulletin # 911076 Date: 101209

3G MMI(R) - Satellite Radio Concerns

91 3G MMI: Satellite radio concerns

91 10 76

2024200/2

December 9, 2010.

Supersedes Technical Service Bulletin Group 91 number 10-51 dated August 18, 2010 for reasons listed below.

Affected Vehicles

Condition

^ Satellite radio band selection is not available using the Radio selection button in the 3G MMI control panel.

^ Satellite radio pre-set stations intermittently disappear.

Technical Background

Software issue in the radio.

Production Solution

New software (ZUG 0114).

Service

Tip: For successful results, the steps must be performed in this sequence.

1. Check 3G MMI system software version

2. Update software of the 3G MMI system

3. Perform feedback documentation to the SVM

1. Check 3G MMI system software version

1. Switch on ignition and wait approximately 1 minute.

247

2. Press the SETUP and RETURN buttons simultaneously and hold both buttons down for about 5 seconds.

If this message is displayed, the system is not yet completely initialized. Wait a few seconds, then press the RETURN button.

3. Read current MMI train (Zug) version.

4. The train (Zug) versions listed in the table below must be updated.

P versions are production build.

K versions are service updates.

2. Update software of the 3G MMI system

1. Connect an approved Audi battery maintainer/charger to vehicle.

2. Switch off all unnecessary electrical equipment (blower, seat heater, interior light, etc.).

Tip: Also make sure that no electromagnetic interference sources (mobile phone) are operated in or near the vehicle while individual control units

are being updated.

248

Tip: For complete and detailed instructions for the 3G MMI system update, refer to the attached instructions. (Note: The attached instructions are

generic. Some portions may not apply to this specific TSB. Importing and exporting customer code data is not necessary for this 3G MMI update

system.)

3. Insert update CD into the 3G MMI main (head) drive unit located in the center of the instrument panel.

4. Start the software update.

5. After the software update has been performed, confirm the "Abort (cancel) documentation" selection. The 3G MMI system will restart. Then

perform the feedback documentation.

3. Perform feedback documentation to the SVM

1. Follow all instructions in the attached TSB 2011732 00 Software Version Management (SVM), operating instructions.

2. Confirm any proposed parameter settings and codings.

3. Then perform test program "5F - Information electronics, resetting fault memory" to clear any faults in the system.

Tip: No control unit is flashed as part of the feedback documentation to the SVM. Do not perform any updates of control units. Do not replace any

control units.

Warranty

249

Required Parts and Tools

Additional information

The following Technical Service Bulletin will be necessary to complete this procedure:

^ TSB 2011732 00 Software Version Management (SVM), operating instructions.

All part and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Dept. and service manuals

for the latest information.

Attachment

250

251

252

253

254

255

256

257

2011732 00 Software Version Management (SVM), operating instructions

Instructions For MMI 3G Nav. Plus Update

Instructions for MMI 3G Nav. Plus update

MMI update programming for vehicles equipped with MMI 3G, e.g. the Audi Q5 (8R) with feedback documentation via Software Versions

Management (Audi SVM).

Overview of the MMI 3G Systems described here with relevant PR no.:

MMI 3G - 8DY

258

1. Overview of controls

259

2. Important information about update programming

260

261

262

263

264

265

266

267

268

269

3. Carrying out update programming

270

271

272

273

4. Changing languages, only for MMI 3G Radio/Basic Plus systems (not available in Audi Q5 models).

274

275

276

277

278

5. Importing and exporting customer data (MMI 3G Navigation Plus)

279

Activating imported customer data.

Audi A4 Quattro Wagon (8K5) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 911076 Date: 101209

Audi A4 Quattro Wagon (8K5) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 911076 Date: 101209

3G MMI(R) - Satellite Radio Concerns

91 3G MMI: Satellite radio concerns

91 10 76

2024200/2

December 9, 2010.

Supersedes Technical Service Bulletin Group 91 number 10-51 dated August 18, 2010 for reasons listed below.

Affected Vehicles

437

Condition

^ Satellite radio band selection is not available using the Radio selection button in the 3G MMI control panel.

^ Satellite radio pre-set stations intermittently disappear.

Technical Background

Software issue in the radio.

Production Solution

New software (ZUG 0114).

Service

Tip: For successful results, the steps must be performed in this sequence.

1. Check 3G MMI system software version

2. Update software of the 3G MMI system

3. Perform feedback documentation to the SVM

1. Check 3G MMI system software version

1. Switch on ignition and wait approximately 1 minute.

2. Press the SETUP and RETURN buttons simultaneously and hold both buttons down for about 5 seconds.

438

If this message is displayed, the system is not yet completely initialized. Wait a few seconds, then press the RETURN button.

3. Read current MMI train (Zug) version.

4. The train (Zug) versions listed in the table below must be updated.

P versions are production build.

K versions are service updates.

2. Update software of the 3G MMI system

1. Connect an approved Audi battery maintainer/charger to vehicle.

2. Switch off all unnecessary electrical equipment (blower, seat heater, interior light, etc.).

Tip: Also make sure that no electromagnetic interference sources (mobile phone) are operated in or near the vehicle while individual control units

are being updated.

Tip: For complete and detailed instructions for the 3G MMI system update, refer to the attached instructions. (Note: The attached instructions are

generic. Some portions may not apply to this specific TSB. Importing and exporting customer code data is not necessary for this 3G MMI update

system.)

3. Insert update CD into the 3G MMI main (head) drive unit located in the center of the instrument panel.

4. Start the software update.

5. After the software update has been performed, confirm the "Abort (cancel) documentation" selection. The 3G MMI system will restart. Then

perform the feedback documentation.

3. Perform feedback documentation to the SVM

1. Follow all instructions in the attached TSB 2011732 00 Software Version Management (SVM), operating instructions.

2. Confirm any proposed parameter settings and codings.

3. Then perform test program "5F - Information electronics, resetting fault memory" to clear any faults in the system.

Tip: No control unit is flashed as part of the feedback documentation to the SVM. Do not perform any updates of control units. Do not replace any

control units.

439

Warranty

Required Parts and Tools

Additional information

The following Technical Service Bulletin will be necessary to complete this procedure:

^ TSB 2011732 00 Software Version Management (SVM), operating instructions.

All part and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Dept. and service manuals

for the latest information.

Attachment

440

441

442

443

444

445

446

447

2011732 00 Software Version Management (SVM), operating instructions

Instructions For MMI 3G Nav. Plus Update

Instructions for MMI 3G Nav. Plus update

MMI update programming for vehicles equipped with MMI 3G, e.g. the Audi Q5 (8R) with feedback documentation via Software Versions

Management (Audi SVM).

Overview of the MMI 3G Systems described here with relevant PR no.:

MMI 3G - 8DY

448

1. Overview of controls

449

2. Important information about update programming

450

451

452

453

454

455

456

457

458

459

3. Carrying out update programming

460

461

462

463

4. Changing languages, only for MMI 3G Radio/Basic Plus systems (not available in Audi Q5 models).

464

465

466

467

468

5. Importing and exporting customer data (MMI 3G Navigation Plus)

469

Activating imported customer data.

Audi A4 Sedan (8K2) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 911076 Date: 101209

Audi A4 Sedan (8K2) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 911076 Date: 101209

3G MMI(R) - Satellite Radio Concerns

91 3G MMI: Satellite radio concerns

91 10 76

2024200/2

December 9, 2010.

Supersedes Technical Service Bulletin Group 91 number 10-51 dated August 18, 2010 for reasons listed below.

Affected Vehicles

431

Condition

^ Satellite radio band selection is not available using the Radio selection button in the 3G MMI control panel.

^ Satellite radio pre-set stations intermittently disappear.

Technical Background

Software issue in the radio.

Production Solution

New software (ZUG 0114).

Service

Tip: For successful results, the steps must be performed in this sequence.

1. Check 3G MMI system software version

2. Update software of the 3G MMI system

3. Perform feedback documentation to the SVM

1. Check 3G MMI system software version

1. Switch on ignition and wait approximately 1 minute.

2. Press the SETUP and RETURN buttons simultaneously and hold both buttons down for about 5 seconds.

432

If this message is displayed, the system is not yet completely initialized. Wait a few seconds, then press the RETURN button.

3. Read current MMI train (Zug) version.

4. The train (Zug) versions listed in the table below must be updated.

P versions are production build.

K versions are service updates.

2. Update software of the 3G MMI system

1. Connect an approved Audi battery maintainer/charger to vehicle.

2. Switch off all unnecessary electrical equipment (blower, seat heater, interior light, etc.).

Tip: Also make sure that no electromagnetic interference sources (mobile phone) are operated in or near the vehicle while individual control units

are being updated.

Tip: For complete and detailed instructions for the 3G MMI system update, refer to the attached instructions. (Note: The attached instructions are

generic. Some portions may not apply to this specific TSB. Importing and exporting customer code data is not necessary for this 3G MMI update

system.)

3. Insert update CD into the 3G MMI main (head) drive unit located in the center of the instrument panel.

4. Start the software update.

5. After the software update has been performed, confirm the "Abort (cancel) documentation" selection. The 3G MMI system will restart. Then

perform the feedback documentation.

3. Perform feedback documentation to the SVM

1. Follow all instructions in the attached TSB 2011732 00 Software Version Management (SVM), operating instructions.

2. Confirm any proposed parameter settings and codings.

3. Then perform test program "5F - Information electronics, resetting fault memory" to clear any faults in the system.

Tip: No control unit is flashed as part of the feedback documentation to the SVM. Do not perform any updates of control units. Do not replace any

control units.

433

Warranty

Required Parts and Tools

Additional information

The following Technical Service Bulletin will be necessary to complete this procedure:

^ TSB 2011732 00 Software Version Management (SVM), operating instructions.

All part and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Dept. and service manuals

for the latest information.

Attachment

434

435

436

437

438

439

440

441

2011732 00 Software Version Management (SVM), operating instructions

Instructions For MMI 3G Nav. Plus Update

Instructions for MMI 3G Nav. Plus update

MMI update programming for vehicles equipped with MMI 3G, e.g. the Audi Q5 (8R) with feedback documentation via Software Versions

Management (Audi SVM).

Overview of the MMI 3G Systems described here with relevant PR no.:

MMI 3G - 8DY

442

1. Overview of controls

443

2. Important information about update programming

444

445

446

447

448

449

450

451

452

453

3. Carrying out update programming

454

455

456

457

4. Changing languages, only for MMI 3G Radio/Basic Plus systems (not available in Audi Q5 models).

458

459

460

461

462

5. Importing and exporting customer data (MMI 3G Navigation Plus)

463

Activating imported customer data.

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 911076 Date: 101209

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 911076 Date: 101209

3G MMI(R) - Satellite Radio Concerns

91 3G MMI: Satellite radio concerns

91 10 76

2024200/2

December 9, 2010.

Supersedes Technical Service Bulletin Group 91 number 10-51 dated August 18, 2010 for reasons listed below.

Affected Vehicles

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 431

Condition

^ Satellite radio band selection is not available using the Radio selection button in the 3G MMI control panel.

^ Satellite radio pre-set stations intermittently disappear.

Technical Background

Software issue in the radio.

Production Solution

New software (ZUG 0114).

Service

Tip: For successful results, the steps must be performed in this sequence.

1. Check 3G MMI system software version

2. Update software of the 3G MMI system

3. Perform feedback documentation to the SVM

1. Check 3G MMI system software version

1. Switch on ignition and wait approximately 1 minute.

2. Press the SETUP and RETURN buttons simultaneously and hold both buttons down for about 5 seconds.

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 432

If this message is displayed, the system is not yet completely initialized. Wait a few seconds, then press the RETURN button.

3. Read current MMI train (Zug) version.

4. The train (Zug) versions listed in the table below must be updated.

P versions are production build.

K versions are service updates.

2. Update software of the 3G MMI system

1. Connect an approved Audi battery maintainer/charger to vehicle.

2. Switch off all unnecessary electrical equipment (blower, seat heater, interior light, etc.).

Tip: Also make sure that no electromagnetic interference sources (mobile phone) are operated in or near the vehicle while individual control units

are being updated.

Tip: For complete and detailed instructions for the 3G MMI system update, refer to the attached instructions. (Note: The attached instructions are

generic. Some portions may not apply to this specific TSB. Importing and exporting customer code data is not necessary for this 3G MMI update

system.)

3. Insert update CD into the 3G MMI main (head) drive unit located in the center of the instrument panel.

4. Start the software update.

5. After the software update has been performed, confirm the "Abort (cancel) documentation" selection. The 3G MMI system will restart. Then

perform the feedback documentation.

3. Perform feedback documentation to the SVM

1. Follow all instructions in the attached TSB 2011732 00 Software Version Management (SVM), operating instructions.

2. Confirm any proposed parameter settings and codings.

3. Then perform test program "5F - Information electronics, resetting fault memory" to clear any faults in the system.

Tip: No control unit is flashed as part of the feedback documentation to the SVM. Do not perform any updates of control units. Do not replace any

control units.

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 433

Warranty

Required Parts and Tools

Additional information

The following Technical Service Bulletin will be necessary to complete this procedure:

^ TSB 2011732 00 Software Version Management (SVM), operating instructions.

All part and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Dept. and service manuals

for the latest information.

Attachment

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 434

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 435

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 436

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 437

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 438

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 439

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 440

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 441

2011732 00 Software Version Management (SVM), operating instructions

Instructions For MMI 3G Nav. Plus Update

Instructions for MMI 3G Nav. Plus update

MMI update programming for vehicles equipped with MMI 3G, e.g. the Audi Q5 (8R) with feedback documentation via Software Versions

Management (Audi SVM).

Overview of the MMI 3G Systems described here with relevant PR no.:

MMI 3G - 8DY

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 442

1. Overview of controls

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 443

2. Important information about update programming

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 444

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 445

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 446

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 447

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 448

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 449

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 450

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 451

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 452

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 453

3. Carrying out update programming

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 454

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 455

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 456

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 457

4. Changing languages, only for MMI 3G Radio/Basic Plus systems (not available in Audi Q5 models).

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 458

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 459

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 460

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 461

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 462

5. Importing and exporting customer data (MMI 3G Navigation Plus)

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 463

Activating imported customer data.

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 464

Audi A5 Cabriolet (8F7) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 911076 Date: 101209

Audi A5 Cabriolet (8F7) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 911076 Date: 101209

3G MMI(R) - Satellite Radio Concerns

91 3G MMI: Satellite radio concerns

91 10 76

2024200/2

December 9, 2010.

Supersedes Technical Service Bulletin Group 91 number 10-51 dated August 18, 2010 for reasons listed below.

Affected Vehicles

405

Condition

^ Satellite radio band selection is not available using the Radio selection button in the 3G MMI control panel.

^ Satellite radio pre-set stations intermittently disappear.

Technical Background

Software issue in the radio.

Production Solution

New software (ZUG 0114).

Service

Tip: For successful results, the steps must be performed in this sequence.

1. Check 3G MMI system software version

2. Update software of the 3G MMI system

3. Perform feedback documentation to the SVM

1. Check 3G MMI system software version

1. Switch on ignition and wait approximately 1 minute.

2. Press the SETUP and RETURN buttons simultaneously and hold both buttons down for about 5 seconds.

406

If this message is displayed, the system is not yet completely initialized. Wait a few seconds, then press the RETURN button.

3. Read current MMI train (Zug) version.

4. The train (Zug) versions listed in the table below must be updated.

P versions are production build.

K versions are service updates.

2. Update software of the 3G MMI system

1. Connect an approved Audi battery maintainer/charger to vehicle.

2. Switch off all unnecessary electrical equipment (blower, seat heater, interior light, etc.).

Tip: Also make sure that no electromagnetic interference sources (mobile phone) are operated in or near the vehicle while individual control units

are being updated.

Tip: For complete and detailed instructions for the 3G MMI system update, refer to the attached instructions. (Note: The attached instructions are

generic. Some portions may not apply to this specific TSB. Importing and exporting customer code data is not necessary for this 3G MMI update

system.)

3. Insert update CD into the 3G MMI main (head) drive unit located in the center of the instrument panel.

4. Start the software update.

5. After the software update has been performed, confirm the "Abort (cancel) documentation" selection. The 3G MMI system will restart. Then

perform the feedback documentation.

3. Perform feedback documentation to the SVM

1. Follow all instructions in the attached TSB 2011732 00 Software Version Management (SVM), operating instructions.

2. Confirm any proposed parameter settings and codings.

3. Then perform test program "5F - Information electronics, resetting fault memory" to clear any faults in the system.

Tip: No control unit is flashed as part of the feedback documentation to the SVM. Do not perform any updates of control units. Do not replace any

control units.

407

Warranty

Required Parts and Tools

Additional information

The following Technical Service Bulletin will be necessary to complete this procedure:

^ TSB 2011732 00 Software Version Management (SVM), operating instructions.

All part and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Dept. and service manuals

for the latest information.

Attachment

408

409

410

411

412

413

414

415

2011732 00 Software Version Management (SVM), operating instructions

Instructions For MMI 3G Nav. Plus Update

Instructions for MMI 3G Nav. Plus update

MMI update programming for vehicles equipped with MMI 3G, e.g. the Audi Q5 (8R) with feedback documentation via Software Versions

Management (Audi SVM).

Overview of the MMI 3G Systems described here with relevant PR no.:

MMI 3G - 8DY

416

1. Overview of controls

417

2. Important information about update programming

418

419

420

421

422

423

424

425

426

427

3. Carrying out update programming

428

429

430

431

4. Changing languages, only for MMI 3G Radio/Basic Plus systems (not available in Audi Q5 models).

432

433

434

435

436

5. Importing and exporting customer data (MMI 3G Navigation Plus)

437

Activating imported customer data.