******** Audi A5 Cabriolet (8F7) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 941306 Date: 130214

Lighting - Erroneous Lamp Malfunction Message Displayed

94 Vehicle lights malfunction message in instrument cluster display

94 13 06

2017806/7

February 14, 2013

Supersedes Technical Service Bulletin Group 94 number 12-79 dated June 6, 2012 for reasons listed.

690

Vehicle Information

Condition

^ Light bulb warning light and the message Vehicle lights: malfunction is displayed in the instrument cluster display.

^ DTC 03280 (Light switch position implausible signal) is stored in the vehicle electrical system control module, J519 (09).

^ Exterior lights are functioning properly.

Technical Background

If the headlight switch is moved to an intermediate position and remains there, the light bulb warning light and the error message appear after

approximately ten seconds (Figure 1).

691

Once displayed, the message turns off after approximately five seconds. The light bulb warning light turns off only after the headlight switch is

turned to a defined position, and the status of DTC 03280 is changed to sporadic.

After 40 driving cycles without an implausible signal detected, the DTC is automatically cleared.

Production Solution

Not applicable.

Service

Determine if the above situation applies to the vehicle, and explain the background to the customer. Replacing parts does not change the behavior.

Warranty

This TSB is informational only and not applicable to any Audi warranty.

Additional Information

All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service

manuals for the latest information.

******** Audi A5 Cabriolet (8F7) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 551327 Date: 130214

Instruments - 'Low Oil Level Message' Displayed

741

55 Oil warning in DIS or MMI

55 13 27

2023967/4

February 14, 2013

Supersedes Technical Service Bulletin Group 55 number 12-24 dated August 7, 2012 for reasons listed.

Vehicle Information

Condition

"Low Oil Level" message is on in the DIS or MMI.

Technical Background

The hood must be open for at least 30 seconds for a reset of this message to be performed. The message is not reset in the DIS/MMI because the

hood has not been recognized as being opened due to an inoperative hood contact switch.

Production Solution

Improved hood contact switches have been put into current production vehicles, and a software change with improved logic is planned for

production.

Service

Check hood contact switch: Use the VAS diagnostic tester to read MVB 26 in the J393 - Comfort System Control Module (address code 46) after

the hood is opened and closed.

If the value does not change, then replace only the contact switch. Follow the applicable work instructions listed in ElsaWeb for replacing the

hood contact switch.

Tip:

Do not replace the complete hood latch assembly. Replace only the micro-switch.

742

There are two suppliers for B8 hood latches. Check the part number on the current contact switch connector to determine which part number must be

ordered: 8T0953236B or 8K0953236A (Figure 1).

The two suppliers use different designs for the contact switch (Figure 2). Therefore, the mounting location is slightly different on the different hood

latches (Figure 3). The contact switches are not cross-compatible between the different latches. However, the latches can be swapped between

vehicles as long as the correct contact switch is installed.

^ If the value in the MVB changes as expected (normal operation of the contact switch), then the vehicle may have an oil level issue. Please check

the oil according to the instructions in the Repair Manual.

743

Warranty

All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures Manual. Claims are subject to

review or audit by Audi Warranty.

Required Parts and Tools

Additional Information

All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service

manuals for the latest information.

******** Audi A4 Sedan (8K2) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 341315 Date: 130214

M/T - Transmission Jumps Out Of 6th Gear

34 - 6th gear jumps out - OB1/OB2 gearbox

34 13 15

2026719/4

February 14, 2013

Supersedes Technical Service Bulletin Group 34 number 13-14 dated June 21, 2013 for reasons listed.

Vehicle Information

754

Condition

The transmission jumps out of 6th gear.

Technical Background

Improved 5th and 6th shift fork and gearshift unit.

Production Solution

Not applicable.

Service

1. Verify shifter mechanism is within specification and adjust accordingly if necessary. ELSA > Transmission > Description and Operation >

Selector Mechanism, Adjusting. Recheck for the concern. If the concern is no longer present, no further repairs are needed.

2. Verify all shift rods are in good working condition.

3. If concern is still present, remove the transmission according to instructions in ELSA.

4. Replace the 5th - 6th gear shift fork and ball sleeve (Item 4 and 5, Figure 1) and the gear shift unit (Item 6 Figure 1) per instructions in ELSA:

Transmission > Manual Transmission Internal Components > 34 Controls, Housing > Disassembly and Assembly > Transmission, Assembly

Sequence AND 35 Gears, Shafts > Disassembly and Assembly > Shift Fork Group, input shaft.

Tip:

When replacing the shift fork and ball sleeve, no further disassembly of input shaft is required.

5. Reinstall transmission and verify proper operation.

755

Warranty

All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures Manual. Claims are subject to

review or audit by Audi Warranty.

Required Parts and Tools

Additional Information

All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service

756

manuals for the latest information.

******** Audi A5 Cabriolet (8F7) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 341315 Date: 130214

M/T - Transmission Jumps Out Of 6th Gear

34 - 6th gear jumps out - OB1/OB2 gearbox

34 13 15

2026719/4

February 14, 2013

Supersedes Technical Service Bulletin Group 34 number 13-14 dated June 21, 2013 for reasons listed.

Vehicle Information

733

Condition

The transmission jumps out of 6th gear.

Technical Background

Improved 5th and 6th shift fork and gearshift unit.

Production Solution

Not applicable.

Service

1. Verify shifter mechanism is within specification and adjust accordingly if necessary. ELSA > Transmission > Description and Operation >

Selector Mechanism, Adjusting. Recheck for the concern. If the concern is no longer present, no further repairs are needed.

2. Verify all shift rods are in good working condition.

3. If concern is still present, remove the transmission according to instructions in ELSA.

4. Replace the 5th - 6th gear shift fork and ball sleeve (Item 4 and 5, Figure 1) and the gear shift unit (Item 6 Figure 1) per instructions in ELSA:

Transmission > Manual Transmission Internal Components > 34 Controls, Housing > Disassembly and Assembly > Transmission, Assembly

Sequence AND 35 Gears, Shafts > Disassembly and Assembly > Shift Fork Group, input shaft.

Tip:

When replacing the shift fork and ball sleeve, no further disassembly of input shaft is required.

5. Reinstall transmission and verify proper operation.

734

Warranty

All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures Manual. Claims are subject to

review or audit by Audi Warranty.

Required Parts and Tools

Additional Information

All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service

735

manuals for the latest information.

******** Audi A4 Quattro Wagon (8K5) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 341315 Date: 130214

M/T - Transmission Jumps Out Of 6th Gear

34 - 6th gear jumps out - OB1/OB2 gearbox

34 13 15

2026719/4

February 14, 2013

Supersedes Technical Service Bulletin Group 34 number 13-14 dated June 21, 2013 for reasons listed.

Vehicle Information

756

Condition

The transmission jumps out of 6th gear.

Technical Background

Improved 5th and 6th shift fork and gearshift unit.

Production Solution

Not applicable.

Service

1. Verify shifter mechanism is within specification and adjust accordingly if necessary. ELSA > Transmission > Description and Operation >

Selector Mechanism, Adjusting. Recheck for the concern. If the concern is no longer present, no further repairs are needed.

2. Verify all shift rods are in good working condition.

3. If concern is still present, remove the transmission according to instructions in ELSA.

4. Replace the 5th - 6th gear shift fork and ball sleeve (Item 4 and 5, Figure 1) and the gear shift unit (Item 6 Figure 1) per instructions in ELSA:

Transmission > Manual Transmission Internal Components > 34 Controls, Housing > Disassembly and Assembly > Transmission, Assembly

Sequence AND 35 Gears, Shafts > Disassembly and Assembly > Shift Fork Group, input shaft.

Tip:

When replacing the shift fork and ball sleeve, no further disassembly of input shaft is required.

5. Reinstall transmission and verify proper operation.

757

Warranty

All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures Manual. Claims are subject to

review or audit by Audi Warranty.

Required Parts and Tools

Additional Information

All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service

758

manuals for the latest information.

******** Audi A4 Sedan (8K2) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 551327 Date: 130214

Instruments - 'Low Oil Level Message' Displayed

762

55 Oil warning in DIS or MMI

55 13 27

2023967/4

February 14, 2013

Supersedes Technical Service Bulletin Group 55 number 12-24 dated August 7, 2012 for reasons listed.

Vehicle Information

Condition

"Low Oil Level" message is on in the DIS or MMI.

Technical Background

The hood must be open for at least 30 seconds for a reset of this message to be performed. The message is not reset in the DIS/MMI because the

hood has not been recognized as being opened due to an inoperative hood contact switch.

Production Solution

Improved hood contact switches have been put into current production vehicles, and a software change with improved logic is planned for

production.

Service

Check hood contact switch: Use the VAS diagnostic tester to read MVB 26 in the J393 - Comfort System Control Module (address code 46) after

the hood is opened and closed.

If the value does not change, then replace only the contact switch. Follow the applicable work instructions listed in ElsaWeb for replacing the

hood contact switch.

Tip:

Do not replace the complete hood latch assembly. Replace only the micro-switch.

763

There are two suppliers for B8 hood latches. Check the part number on the current contact switch connector to determine which part number must be

ordered: 8T0953236B or 8K0953236A (Figure 1).

The two suppliers use different designs for the contact switch (Figure 2). Therefore, the mounting location is slightly different on the different hood

latches (Figure 3). The contact switches are not cross-compatible between the different latches. However, the latches can be swapped between

vehicles as long as the correct contact switch is installed.

^ If the value in the MVB changes as expected (normal operation of the contact switch), then the vehicle may have an oil level issue. Please check

the oil according to the instructions in the Repair Manual.

764

Warranty

All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures Manual. Claims are subject to

review or audit by Audi Warranty.

Required Parts and Tools

Additional Information

All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service

manuals for the latest information.

******** Audi A4 Sedan (8K2) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 941306 Date: 130214

Lighting - Erroneous Lamp Malfunction Message Displayed

94 Vehicle lights malfunction message in instrument cluster display

94 13 06

2017806/7

February 14, 2013

Supersedes Technical Service Bulletin Group 94 number 12-79 dated June 6, 2012 for reasons listed.

711

Vehicle Information

Condition

^ Light bulb warning light and the message Vehicle lights: malfunction is displayed in the instrument cluster display.

^ DTC 03280 (Light switch position implausible signal) is stored in the vehicle electrical system control module, J519 (09).

^ Exterior lights are functioning properly.

Technical Background

If the headlight switch is moved to an intermediate position and remains there, the light bulb warning light and the error message appear after

approximately ten seconds (Figure 1).

712

Once displayed, the message turns off after approximately five seconds. The light bulb warning light turns off only after the headlight switch is

turned to a defined position, and the status of DTC 03280 is changed to sporadic.

After 40 driving cycles without an implausible signal detected, the DTC is automatically cleared.

Production Solution

Not applicable.

Service

Determine if the above situation applies to the vehicle, and explain the background to the customer. Replacing parts does not change the behavior.

Warranty

This TSB is informational only and not applicable to any Audi warranty.

Additional Information

All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service

manuals for the latest information.

******** Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 341315 Date: 130214

M/T - Transmission Jumps Out Of 6th Gear

34 - 6th gear jumps out - OB1/OB2 gearbox

34 13 15

2026719/4

February 14, 2013

Supersedes Technical Service Bulletin Group 34 number 13-14 dated June 21, 2013 for reasons listed.

Vehicle Information

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 731

Condition

The transmission jumps out of 6th gear.

Technical Background

Improved 5th and 6th shift fork and gearshift unit.

Production Solution

Not applicable.

Service

1. Verify shifter mechanism is within specification and adjust accordingly if necessary. ELSA > Transmission > Description and Operation >

Selector Mechanism, Adjusting. Recheck for the concern. If the concern is no longer present, no further repairs are needed.

2. Verify all shift rods are in good working condition.

3. If concern is still present, remove the transmission according to instructions in ELSA.

4. Replace the 5th - 6th gear shift fork and ball sleeve (Item 4 and 5, Figure 1) and the gear shift unit (Item 6 Figure 1) per instructions in ELSA:

Transmission > Manual Transmission Internal Components > 34 Controls, Housing > Disassembly and Assembly > Transmission, Assembly

Sequence AND 35 Gears, Shafts > Disassembly and Assembly > Shift Fork Group, input shaft.

Tip:

When replacing the shift fork and ball sleeve, no further disassembly of input shaft is required.

5. Reinstall transmission and verify proper operation.

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 732

Warranty

All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures Manual. Claims are subject to

review or audit by Audi Warranty.

Required Parts and Tools

Additional Information

All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 733

manuals for the latest information.

******** Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 551327 Date: 130214

Instruments - 'Low Oil Level Message' Displayed

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 739

55 Oil warning in DIS or MMI

55 13 27

2023967/4

February 14, 2013

Supersedes Technical Service Bulletin Group 55 number 12-24 dated August 7, 2012 for reasons listed.

Vehicle Information

Condition

"Low Oil Level" message is on in the DIS or MMI.

Technical Background

The hood must be open for at least 30 seconds for a reset of this message to be performed. The message is not reset in the DIS/MMI because the

hood has not been recognized as being opened due to an inoperative hood contact switch.

Production Solution

Improved hood contact switches have been put into current production vehicles, and a software change with improved logic is planned for

production.

Service

Check hood contact switch: Use the VAS diagnostic tester to read MVB 26 in the J393 - Comfort System Control Module (address code 46) after

the hood is opened and closed.

If the value does not change, then replace only the contact switch. Follow the applicable work instructions listed in ElsaWeb for replacing the

hood contact switch.

Tip:

Do not replace the complete hood latch assembly. Replace only the micro-switch.

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 740

There are two suppliers for B8 hood latches. Check the part number on the current contact switch connector to determine which part number must be

ordered: 8T0953236B or 8K0953236A (Figure 1).

The two suppliers use different designs for the contact switch (Figure 2). Therefore, the mounting location is slightly different on the different hood

latches (Figure 3). The contact switches are not cross-compatible between the different latches. However, the latches can be swapped between

vehicles as long as the correct contact switch is installed.

^ If the value in the MVB changes as expected (normal operation of the contact switch), then the vehicle may have an oil level issue. Please check

the oil according to the instructions in the Repair Manual.

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 741

Warranty

All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures Manual. Claims are subject to

review or audit by Audi Warranty.

Required Parts and Tools

Additional Information

All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service

manuals for the latest information.

******** Audi A4 Quattro Wagon (8K5) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 551327 Date: 130214

Instruments - 'Low Oil Level Message' Displayed

764

55 Oil warning in DIS or MMI

55 13 27

2023967/4

February 14, 2013

Supersedes Technical Service Bulletin Group 55 number 12-24 dated August 7, 2012 for reasons listed.

Vehicle Information

Condition

"Low Oil Level" message is on in the DIS or MMI.

Technical Background

The hood must be open for at least 30 seconds for a reset of this message to be performed. The message is not reset in the DIS/MMI because the

hood has not been recognized as being opened due to an inoperative hood contact switch.

Production Solution

Improved hood contact switches have been put into current production vehicles, and a software change with improved logic is planned for

production.

Service

Check hood contact switch: Use the VAS diagnostic tester to read MVB 26 in the J393 - Comfort System Control Module (address code 46) after

the hood is opened and closed.

If the value does not change, then replace only the contact switch. Follow the applicable work instructions listed in ElsaWeb for replacing the

hood contact switch.

Tip:

Do not replace the complete hood latch assembly. Replace only the micro-switch.

765

There are two suppliers for B8 hood latches. Check the part number on the current contact switch connector to determine which part number must be

ordered: 8T0953236B or 8K0953236A (Figure 1).

The two suppliers use different designs for the contact switch (Figure 2). Therefore, the mounting location is slightly different on the different hood

latches (Figure 3). The contact switches are not cross-compatible between the different latches. However, the latches can be swapped between

vehicles as long as the correct contact switch is installed.

^ If the value in the MVB changes as expected (normal operation of the contact switch), then the vehicle may have an oil level issue. Please check

the oil according to the instructions in the Repair Manual.

766

Warranty

All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures Manual. Claims are subject to

review or audit by Audi Warranty.

Required Parts and Tools

Additional Information

All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service

manuals for the latest information.

******** Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 941306 Date: 130214

Lighting - Erroneous Lamp Malfunction Message Displayed

94 Vehicle lights malfunction message in instrument cluster display

94 13 06

2017806/7

February 14, 2013

Supersedes Technical Service Bulletin Group 94 number 12-79 dated June 6, 2012 for reasons listed.

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 688

Vehicle Information

Condition

^ Light bulb warning light and the message Vehicle lights: malfunction is displayed in the instrument cluster display.

^ DTC 03280 (Light switch position implausible signal) is stored in the vehicle electrical system control module, J519 (09).

^ Exterior lights are functioning properly.

Technical Background

If the headlight switch is moved to an intermediate position and remains there, the light bulb warning light and the error message appear after

approximately ten seconds (Figure 1).

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 689

Once displayed, the message turns off after approximately five seconds. The light bulb warning light turns off only after the headlight switch is

turned to a defined position, and the status of DTC 03280 is changed to sporadic.

After 40 driving cycles without an implausible signal detected, the DTC is automatically cleared.

Production Solution

Not applicable.

Service

Determine if the above situation applies to the vehicle, and explain the background to the customer. Replacing parts does not change the behavior.

Warranty

This TSB is informational only and not applicable to any Audi warranty.

Additional Information

All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service

manuals for the latest information.

******** Audi A4 Quattro Wagon (8K5) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 941306 Date: 130214

Lighting - Erroneous Lamp Malfunction Message Displayed

94 Vehicle lights malfunction message in instrument cluster display

94 13 06

2017806/7

February 14, 2013

Supersedes Technical Service Bulletin Group 94 number 12-79 dated June 6, 2012 for reasons listed.

713

Vehicle Information

Condition

^ Light bulb warning light and the message Vehicle lights: malfunction is displayed in the instrument cluster display.

^ DTC 03280 (Light switch position implausible signal) is stored in the vehicle electrical system control module, J519 (09).

^ Exterior lights are functioning properly.

Technical Background

If the headlight switch is moved to an intermediate position and remains there, the light bulb warning light and the error message appear after

approximately ten seconds (Figure 1).

714

Once displayed, the message turns off after approximately five seconds. The light bulb warning light turns off only after the headlight switch is

turned to a defined position, and the status of DTC 03280 is changed to sporadic.

After 40 driving cycles without an implausible signal detected, the DTC is automatically cleared.

Production Solution

Not applicable.

Service

Determine if the above situation applies to the vehicle, and explain the background to the customer. Replacing parts does not change the behavior.

Warranty

This TSB is informational only and not applicable to any Audi warranty.

Additional Information

All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service

manuals for the latest information.

Audi A5 Cabriolet (8F7) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 341315 Date: 130214

Audi A5 Cabriolet (8F7) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 341315 Date: 130214

M/T - Transmission Jumps Out Of 6th Gear

34 - 6th gear jumps out - OB1/OB2 gearbox

34 13 15

2026719/4

February 14, 2013

Supersedes Technical Service Bulletin Group 34 number 13-14 dated June 21, 2013 for reasons listed.

Vehicle Information

733

Condition

The transmission jumps out of 6th gear.

Technical Background

Improved 5th and 6th shift fork and gearshift unit.

Production Solution

Not applicable.

Service

1. Verify shifter mechanism is within specification and adjust accordingly if necessary. ELSA > Transmission > Description and Operation >

Selector Mechanism, Adjusting. Recheck for the concern. If the concern is no longer present, no further repairs are needed.

2. Verify all shift rods are in good working condition.

3. If concern is still present, remove the transmission according to instructions in ELSA.

4. Replace the 5th - 6th gear shift fork and ball sleeve (Item 4 and 5, Figure 1) and the gear shift unit (Item 6 Figure 1) per instructions in ELSA:

Transmission > Manual Transmission Internal Components > 34 Controls, Housing > Disassembly and Assembly > Transmission, Assembly

Sequence AND 35 Gears, Shafts > Disassembly and Assembly > Shift Fork Group, input shaft.

Tip:

When replacing the shift fork and ball sleeve, no further disassembly of input shaft is required.

5. Reinstall transmission and verify proper operation.

734

Warranty

All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures Manual. Claims are subject to

review or audit by Audi Warranty.

Required Parts and Tools

Additional Information

All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service

735

manuals for the latest information.

Audi A4 Sedan (8K2) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 341315 Date: 130214

Audi A4 Sedan (8K2) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 341315 Date: 130214

M/T - Transmission Jumps Out Of 6th Gear

34 - 6th gear jumps out - OB1/OB2 gearbox

34 13 15

2026719/4

February 14, 2013

Supersedes Technical Service Bulletin Group 34 number 13-14 dated June 21, 2013 for reasons listed.

Vehicle Information

754

Condition

The transmission jumps out of 6th gear.

Technical Background

Improved 5th and 6th shift fork and gearshift unit.

Production Solution

Not applicable.

Service

1. Verify shifter mechanism is within specification and adjust accordingly if necessary. ELSA > Transmission > Description and Operation >

Selector Mechanism, Adjusting. Recheck for the concern. If the concern is no longer present, no further repairs are needed.

2. Verify all shift rods are in good working condition.

3. If concern is still present, remove the transmission according to instructions in ELSA.

4. Replace the 5th - 6th gear shift fork and ball sleeve (Item 4 and 5, Figure 1) and the gear shift unit (Item 6 Figure 1) per instructions in ELSA:

Transmission > Manual Transmission Internal Components > 34 Controls, Housing > Disassembly and Assembly > Transmission, Assembly

Sequence AND 35 Gears, Shafts > Disassembly and Assembly > Shift Fork Group, input shaft.

Tip:

When replacing the shift fork and ball sleeve, no further disassembly of input shaft is required.

5. Reinstall transmission and verify proper operation.

755

Warranty

All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures Manual. Claims are subject to

review or audit by Audi Warranty.

Required Parts and Tools

Additional Information

All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service

756

manuals for the latest information.

Audi A5 Cabriolet (8F7) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 551327 Date: 130214

Audi A5 Cabriolet (8F7) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 551327 Date: 130214

Instruments - 'Low Oil Level Message' Displayed

741

55 Oil warning in DIS or MMI

55 13 27

2023967/4

February 14, 2013

Supersedes Technical Service Bulletin Group 55 number 12-24 dated August 7, 2012 for reasons listed.

Vehicle Information

Condition

"Low Oil Level" message is on in the DIS or MMI.

Technical Background

The hood must be open for at least 30 seconds for a reset of this message to be performed. The message is not reset in the DIS/MMI because the

hood has not been recognized as being opened due to an inoperative hood contact switch.

Production Solution

Improved hood contact switches have been put into current production vehicles, and a software change with improved logic is planned for

production.

Service

Check hood contact switch: Use the VAS diagnostic tester to read MVB 26 in the J393 - Comfort System Control Module (address code 46) after

the hood is opened and closed.

If the value does not change, then replace only the contact switch. Follow the applicable work instructions listed in ElsaWeb for replacing the

hood contact switch.

Tip:

Do not replace the complete hood latch assembly. Replace only the micro-switch.

742

There are two suppliers for B8 hood latches. Check the part number on the current contact switch connector to determine which part number must be

ordered: 8T0953236B or 8K0953236A (Figure 1).

The two suppliers use different designs for the contact switch (Figure 2). Therefore, the mounting location is slightly different on the different hood

latches (Figure 3). The contact switches are not cross-compatible between the different latches. However, the latches can be swapped between

vehicles as long as the correct contact switch is installed.

^ If the value in the MVB changes as expected (normal operation of the contact switch), then the vehicle may have an oil level issue. Please check

the oil according to the instructions in the Repair Manual.

743

Warranty

All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures Manual. Claims are subject to

review or audit by Audi Warranty.

Required Parts and Tools

Additional Information

All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service

manuals for the latest information.

Audi A4 Quattro Wagon (8K5) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 341315 Date: 130214

Audi A4 Quattro Wagon (8K5) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 341315 Date: 130214

M/T - Transmission Jumps Out Of 6th Gear

34 - 6th gear jumps out - OB1/OB2 gearbox

34 13 15

2026719/4

February 14, 2013

Supersedes Technical Service Bulletin Group 34 number 13-14 dated June 21, 2013 for reasons listed.

Vehicle Information

756

Condition

The transmission jumps out of 6th gear.

Technical Background

Improved 5th and 6th shift fork and gearshift unit.

Production Solution

Not applicable.

Service

1. Verify shifter mechanism is within specification and adjust accordingly if necessary. ELSA > Transmission > Description and Operation >

Selector Mechanism, Adjusting. Recheck for the concern. If the concern is no longer present, no further repairs are needed.

2. Verify all shift rods are in good working condition.

3. If concern is still present, remove the transmission according to instructions in ELSA.

4. Replace the 5th - 6th gear shift fork and ball sleeve (Item 4 and 5, Figure 1) and the gear shift unit (Item 6 Figure 1) per instructions in ELSA:

Transmission > Manual Transmission Internal Components > 34 Controls, Housing > Disassembly and Assembly > Transmission, Assembly

Sequence AND 35 Gears, Shafts > Disassembly and Assembly > Shift Fork Group, input shaft.

Tip:

When replacing the shift fork and ball sleeve, no further disassembly of input shaft is required.

5. Reinstall transmission and verify proper operation.

757

Warranty

All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures Manual. Claims are subject to

review or audit by Audi Warranty.

Required Parts and Tools

Additional Information

All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service

758

manuals for the latest information.

Audi A4 Quattro Wagon (8K5) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 551327 Date: 130214

Audi A4 Quattro Wagon (8K5) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 551327 Date: 130214

Instruments - 'Low Oil Level Message' Displayed

764

55 Oil warning in DIS or MMI

55 13 27

2023967/4

February 14, 2013

Supersedes Technical Service Bulletin Group 55 number 12-24 dated August 7, 2012 for reasons listed.

Vehicle Information

Condition

"Low Oil Level" message is on in the DIS or MMI.

Technical Background

The hood must be open for at least 30 seconds for a reset of this message to be performed. The message is not reset in the DIS/MMI because the

hood has not been recognized as being opened due to an inoperative hood contact switch.

Production Solution

Improved hood contact switches have been put into current production vehicles, and a software change with improved logic is planned for

production.

Service

Check hood contact switch: Use the VAS diagnostic tester to read MVB 26 in the J393 - Comfort System Control Module (address code 46) after

the hood is opened and closed.

If the value does not change, then replace only the contact switch. Follow the applicable work instructions listed in ElsaWeb for replacing the

hood contact switch.

Tip:

Do not replace the complete hood latch assembly. Replace only the micro-switch.

765

There are two suppliers for B8 hood latches. Check the part number on the current contact switch connector to determine which part number must be

ordered: 8T0953236B or 8K0953236A (Figure 1).

The two suppliers use different designs for the contact switch (Figure 2). Therefore, the mounting location is slightly different on the different hood

latches (Figure 3). The contact switches are not cross-compatible between the different latches. However, the latches can be swapped between

vehicles as long as the correct contact switch is installed.

^ If the value in the MVB changes as expected (normal operation of the contact switch), then the vehicle may have an oil level issue. Please check

the oil according to the instructions in the Repair Manual.

766

Warranty

All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures Manual. Claims are subject to

review or audit by Audi Warranty.

Required Parts and Tools

Additional Information

All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service

manuals for the latest information.

Audi A5 Cabriolet (8F7) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 941306 Date: 130214

Audi A5 Cabriolet (8F7) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 941306 Date: 130214

Lighting - Erroneous Lamp Malfunction Message Displayed

94 Vehicle lights malfunction message in instrument cluster display

94 13 06

2017806/7

February 14, 2013

Supersedes Technical Service Bulletin Group 94 number 12-79 dated June 6, 2012 for reasons listed.

690

Vehicle Information

Condition

^ Light bulb warning light and the message Vehicle lights: malfunction is displayed in the instrument cluster display.

^ DTC 03280 (Light switch position implausible signal) is stored in the vehicle electrical system control module, J519 (09).

^ Exterior lights are functioning properly.

Technical Background

If the headlight switch is moved to an intermediate position and remains there, the light bulb warning light and the error message appear after

approximately ten seconds (Figure 1).

691

Once displayed, the message turns off after approximately five seconds. The light bulb warning light turns off only after the headlight switch is

turned to a defined position, and the status of DTC 03280 is changed to sporadic.

After 40 driving cycles without an implausible signal detected, the DTC is automatically cleared.

Production Solution

Not applicable.

Service

Determine if the above situation applies to the vehicle, and explain the background to the customer. Replacing parts does not change the behavior.

Warranty

This TSB is informational only and not applicable to any Audi warranty.

Additional Information

All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service

manuals for the latest information.

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 941306 Date: 130214

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 941306 Date: 130214

Lighting - Erroneous Lamp Malfunction Message Displayed

94 Vehicle lights malfunction message in instrument cluster display

94 13 06

2017806/7

February 14, 2013

Supersedes Technical Service Bulletin Group 94 number 12-79 dated June 6, 2012 for reasons listed.

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 688

Vehicle Information

Condition

^ Light bulb warning light and the message Vehicle lights: malfunction is displayed in the instrument cluster display.

^ DTC 03280 (Light switch position implausible signal) is stored in the vehicle electrical system control module, J519 (09).

^ Exterior lights are functioning properly.

Technical Background

If the headlight switch is moved to an intermediate position and remains there, the light bulb warning light and the error message appear after

approximately ten seconds (Figure 1).

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 689

Once displayed, the message turns off after approximately five seconds. The light bulb warning light turns off only after the headlight switch is

turned to a defined position, and the status of DTC 03280 is changed to sporadic.

After 40 driving cycles without an implausible signal detected, the DTC is automatically cleared.

Production Solution

Not applicable.

Service

Determine if the above situation applies to the vehicle, and explain the background to the customer. Replacing parts does not change the behavior.

Warranty

This TSB is informational only and not applicable to any Audi warranty.

Additional Information

All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service

manuals for the latest information.

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 341315 Date: 130214

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Technical Service Bulletin # 341315 Date: 130214

M/T - Transmission Jumps Out Of 6th Gear

34 - 6th gear jumps out - OB1/OB2 gearbox

34 13 15

2026719/4

February 14, 2013

Supersedes Technical Service Bulletin Group 34 number 13-14 dated June 21, 2013 for reasons listed.

Vehicle Information

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 731

Condition

The transmission jumps out of 6th gear.

Technical Background

Improved 5th and 6th shift fork and gearshift unit.

Production Solution

Not applicable.

Service

1. Verify shifter mechanism is within specification and adjust accordingly if necessary. ELSA > Transmission > Description and Operation >

Selector Mechanism, Adjusting. Recheck for the concern. If the concern is no longer present, no further repairs are needed.

2. Verify all shift rods are in good working condition.

3. If concern is still present, remove the transmission according to instructions in ELSA.

4. Replace the 5th - 6th gear shift fork and ball sleeve (Item 4 and 5, Figure 1) and the gear shift unit (Item 6 Figure 1) per instructions in ELSA:

Transmission > Manual Transmission Internal Components > 34 Controls, Housing > Disassembly and Assembly > Transmission, Assembly

Sequence AND 35 Gears, Shafts > Disassembly and Assembly > Shift Fork Group, input shaft.

Tip:

When replacing the shift fork and ball sleeve, no further disassembly of input shaft is required.

5. Reinstall transmission and verify proper operation.

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 732

Warranty

All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures Manual. Claims are subject to

review or audit by Audi Warranty.

Required Parts and Tools

Additional Information

All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service

Audi A4 Quattro Sedan (8K2) L4-2.0L Turbo (CAEB) Page 733

manuals for the latest information.