Alarm System - Installation Kit Part Information
SI M 65 03 03
Sound System, Cruise, Alarms, Monitors
December 2003
Service Engineering
This Service Information bulletin supersedes S.I. M65 03 03 dated September 2003.
[NEW] designates changes to this revision
SUBJECT
Alarm Installation Kit P/N 82 11 0 306 852
MODEL
Cooper - produced as of 9/03
Cooper S produced as of 9/03
SITUATION
Certain components in the MINI Alarm Installation kit P/N 82 11 0 300 295 are no longer valid for vehicles produced as of 9/03. The Alarm Siren
and Tilt Sensor have been integrated into one component and will be located in the same area as the Alarm Siren for earlier production vehicles,
which also results in a new mounting bracket for the siren as well as a new 6 pin connector on the wiring harness.
[NEW] The components required to complete the new MINI Alarm Installation Kit P/N 82 11 0 306 852 are available. Installation instructions may
not be included in the kit and as a result are provided as an attachment to this bulletin.
[NEW] CORRECTION
Please utilize the instructions when installing the Alarm Installation Kit P/N 82 11 0 306 852.
ATTACHMENTS
view PDF attachment M6SO3O3Install.
Installation Instructions
November 2003
Product Development
Installation Instructions
Sound System, Cruise, Alarms
SUBJECT
MINI Alarm Installation Kit - P/N 82 11 0 306 852
MODELS
MINI Cooper (R50): Vehicle Production as of 09/2003
MINI Cooper S (R53): Vehicle Production as of 09/2003
SUGGESTED INSTALLATION TIME: 75 hour
2002-2006 Mini Cooper (R50) L4-1.6L (W10) Page 119
These instructions were developed specifically for MINI vehicles and are not to be compared to any existing instructions for vehicles other than
MINI. No methods other than those specified in this document are to be used to install the MINI Hands-Free Phone System with Bluetooth(TM)
Wireless Technology in MINI vehicles.
PARTS INFORMATION
INSTALLATION PROCEDURE:
1. Disconnect Battery prior to starting the installation.
2. Remove the cover (1) for the Ultrasonic Module located above rear seat.
3. Place the Ultrasonic Module (5) into the cover (6) making certain that the arrows on the module and the cover are aligned.
^ Clip the module into the cover.
2002-2006 Mini Cooper (R50) L4-1.6L (W10) Page 120
4. Connect the module (5) to connector X1582. Reinstall the cover.
5. Attach the Power Siren (1) to the mounting bracket (2) using an M6 nut (3).
6. The black 4-pin connector X19562 (1) located in the left rear corner of the engine compartment near the ABS/ASC Hydraulic module is taped
to the wiring harness.
^ Carefully remove the tape that secures the connector to the harness (1).
7. Connect the black 6 pin connector (2) to the siren (1).
2002-2006 Mini Cooper (R50) L4-1.6L (W10) Page 121
8. Remove the plastic film covering the mounting hole for the siren bracket (1).
9. Secure the mounting bracket and siren (1) into place using a hexagonal screw M6x12 (10) and Hexagonal nut (13).
10. Remove lower section of steering column trim:
^ Remove ignition switch rubber (1)
^ Remove screws (2)
11. Remove knee bolster (1) by carefully pulling the plastic cover forward.
2002-2006 Mini Cooper (R50) L4-1.6L (W10) Page 122
12. Remove lower trim cover:
^ Release lower trim cover (1) retaining clips (4).
^ Remove lower trim cover by pressing in on the upper trim cover (arrow).
13. Remove upper section of steering column trim:
^ Remove two screws (1) at rear of gauges.
^ Disconnect plug.
^ Remove remote gauge cluster.
^ Remove upper trim cover.
14. Remove the wiper switch:
^ Remove screw (1).
^ Remove the wiper switch (arrow).
^ Disconnect connector (2).
2002-2006 Mini Cooper (R50) L4-1.6L (W10) Page 123
15. Install the new wiper switch (1) with anti-theft status indicator.
Note:
The removed wiper switch should be returned to the customer when the vehicle is picked up.
16. Reinstall all removed components and trim covers.
17. Reconnect Battery.
CODING OF THE CONTROL MODULE
After installing this alarm kit the vehicle must be re-coded using the "Retrofit" path to ensure that the alarm works properly with the systems
currently installed in the vehicle. The recoding is done automatically when using the "retrofit" path on the DIS or GT1.
"Retrofit" re-coding steps:
^ Connect DIS or GT1 to vehicle
^ Turn on ignition
^ Select "Coding ZCS"
^ Series: "R50"
^ Path: "2 Retrofit"
^ System: "Alarm system"
FUNCTION TEST
2002-2006 Mini Cooper (R50) L4-1.6L (W10) Page 124
Upon completion of the recoding, verify that the alarm system is working correctly by going through the following action steps, after completing
each step ensure that the desired result is obtained:
2002-2006 Mini Cooper (R50) L4-1.6L (W10) Page 125
