Showing posts with label A/T. Show all posts
Showing posts with label A/T. Show all posts

Thursday, 15 October 2020

******** Audi A8L Quattro Sedan (4E8) V8-4.2L (BVJ) Technical DIAGNOSIS AND REPAIR # 391003 Date: 100629


A/T, Drivetrain - Vibrations On Tight Turns



37 Vibrations on tight turns



39 10 03



2022896/1



June 29, 2010



Affected Vehicles



203



Condition



Customer may report vibrations, humming noises or rubbing noises from the drivetrain when driving slowly around very tight turns. The noise is



particularly noticeable when maneuvering at full steering wheel lock in a parking lot.



Technical Background



Friction-reducing additives in the differential oil are reduced by wear. At high load on tight turns, the friction discs and worm wheel teeth in the



center differential are subject to wear.



This changes the friction and locking values in the center differential and causes vibrations in the drivetrain.



Production Solution



Service



Test drive the vehicle.



^ Light vibrations at full steering wheel lock are normal.



^ With stronger than normal vibrations in minor corners or heavy vibration at full steering wheel lock, proceed as follows:



a. Check the center differential according to the repair manual for correct oil level and inspect for damage (metal shavings).



b. Ensure the wheels are not damaged (bent) and all four tires are the correct size and the same type of tire.



c. If nothing is found, change the oil of the center differential with G 055 145 A2.



The center differential does not have a drain plug, therefore the gear oil can be drained only by removing the cover.



Follow the repair manual directions for removal and installation of the Self-Locking Center Differential Cover but only remove the cover far



enough to drain the oil. Then reassemble and fill with the new G 055 145 A2 oil.



d. Drive the vehicle along a lot of bends until the gearbox temperature reaches 80锟斤拷C and reassess the vibrations.



- If the vibrations have been reduced to normal, the concern is repaired.



- If the oil change does not repair the concern, submit a Technical Assistance Center ticket under the Concern Type: Audi Automatic



Transmission.



Warranty



204



Required Parts and Tools



Additional Information



All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service



manuals for the latest information.

Monday, 10 December 2018

******** Audi A6 Sedan (4F2) V6-3.2L (CALA) Technical DIAGNOSIS AND REPAIR # 391003 Date: 100629


A/T, Drivetrain - Vibrations On Tight Turns



37 Vibrations on tight turns



39 10 03



2022896/1



June 29, 2010



Affected Vehicles



Condition



Customer may report vibrations, humming noises or rubbing noises from the drivetrain when driving slowly around very tight turns. The noise is



particularly noticeable when maneuvering at full steering wheel lock in a parking lot.



Technical Background



Friction-reducing additives in the differential oil are reduced by wear. At high load on tight turns, the friction discs and worm wheel teeth in the



351



center differential are subject to wear.



This changes the friction and locking values in the center differential and causes vibrations in the drivetrain.



Production Solution



Service



Test drive the vehicle.



^ Light vibrations at full steering wheel lock are normal.



^ With stronger than normal vibrations in minor corners or heavy vibration at full steering wheel lock, proceed as follows:



a. Check the center differential according to the repair manual for correct oil level and inspect for damage (metal shavings).



b. Ensure the wheels are not damaged (bent) and all four tires are the correct size and the same type of tire.



c. If nothing is found, change the oil of the center differential with G 055 145 A2.



The center differential does not have a drain plug, therefore the gear oil can be drained only by removing the cover.



Follow the repair manual directions for removal and installation of the Self-Locking Center Differential Cover but only remove the cover far



enough to drain the oil. Then reassemble and fill with the new G 055 145 A2 oil.



d. Drive the vehicle along a lot of bends until the gearbox temperature reaches 80锟斤拷C and reassess the vibrations.



- If the vibrations have been reduced to normal, the concern is repaired.



- If the oil change does not repair the concern, submit a Technical Assistance Center ticket under the Concern Type: Audi Automatic



Transmission.



Warranty



Required Parts and Tools



Additional Information



All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service



manuals for the latest information.

Thursday, 8 November 2018

A/T, CVT Transmission - Howling Noise


A/T, CVT Transmission - Howling Noise



SI M 24 02 06



Automatic Transmission



January 2007



Technical Service



This Service Information bulletin supersedes S.I. M24 02 06 dated May 2006.



[NEW] designates changes to this revision



SUBJECT



CVT - Howling Noise from the Transmission



MODEL



R50 W10 with CVT up to 05/2005



SITUATION



The customer may complain about a howling type of noise coming from the CVT transmission, when the gear selector is placed in D, M, or S



position and the vehicle speed exceeds 5 mph.



The noise description may vary from "rattling" to "howling", depending on the degree of main bearing wear. The frequency of the noise increases



with the engine speed.



This noise is not present with the gear selector in N or P position and the vehicle at a standstill, with engine running at idle.



CAUSE



Excessive wear of the main ball bearing in the CVT transmission.



2002-2006 Mini Cooper (R50) L4-1.6L (W10) Page 264



CORRECTION



On a customer complaint basis only, replace the main CVT ball bearing together with the flange bolts, cover & oil pump O-rings and the plate



spring. For replacement instructions and tightening torques, refer to the [NEW] updated procedure below.



The special tools required to perform this repair: "M35 Socket" - P/N 83 30 0 494 914; "Bearing extractor kit" P/N 83 30 0 494 915; and "Bearing



driver" P/N 83 30 0 494 916 were shipped to all MINI dealers via the Automatic Tool Shipment Program (refer to SI M04 01 06).



[NEW] PROCEDURE



1. Remove front left wheel.



2. Remove left side wheel arch cover.



3. Remove thee bolts with clips securing the primary oil pump cover. Remove the primary cover.



4. Remove 4 M6x8 bolts (1) securing engine pitot chamber to oil pump drive.



Note on installation:



Install 4 new M6 bolts. Tightening



torque: 10 Nm.



5. Rotate the pitot chamber (1) until the flange bolt M6x55 (2), which secures engine pitot tube, can be visible.



6. Unscrew M6x55 bolt (2).



Note on installation:



Tightening torque: 10 Nm



2002-2006 Mini Cooper (R50) L4-1.6L (W10) Page 265



7. Rotate the pitot tube (1) 180锟斤拷 anticlockwise and remove it from the pitot chamber (2).



Note on installation:



Make sure to clean pitot chamber from any debris/oil residue prior to installation.



8. Remove 5 bolts M6x55 (1) securing the oil pump.



9. Remove inlet pressure tube (2).



Note on installation:



M6x55 bolts tightening torque: 10 Nm



10. Carefully remove oil pump (1) out



of the housing.



Note: you need to slightly pull transmission down (using a suitable prying bar) in order to safety clear a chassis member when removing pump out of



the housing.



11. Remove and discard two o-rings



(1). Install new o-rings (provided)



when reassembling.



2002-2006 Mini Cooper (R50) L4-1.6L (W10) Page 266



12. Discard plate spring (2).



13. Make clear marks on both M35X1.5 nut and primary shaft to identify their original position (both markings identified by an



arrow).



14. Using special socket (P/N 83 30 0 494 914) and an impact wrench with a torque capacity of 300 Nm, remove primary bearing nut (1).



Note on installation:



Replace plate spring.



Clean threads on both M35 nut and a



shaft (do not remove markings).



Make sure the primary pitot tube is not



twisted (points to the right).



Apply small amount of Loctite(R) 271 on



the threads and using an impact wrench



for a sufficient duration, tighten the nut



until marks are in line (+/- 5锟斤拷).



15. Using a small screwdriver, lever out seal from the primary bearing.



16. Remove the primary bearing using



"Bearing extractor kit" P/N 83 30 0 494 915.



2002-2006 Mini Cooper (R50) L4-1.6L (W10) Page 267



17. Clean primary bearing bore and shaft.



18. Clean sealant residue from threads in oil pump drive shaft and clean oil pump housing.



19. Drive new main ball bearing into position using "Bearing driver" P/N 83 30 0 494 916.94 916.



20. Reinstall oil pump.



21. Replace o-ring (1) for the main cover.



22. Reinstall all previously removed components.



23. Top-up transmission fluid with ESSO EZL 799.



PARTS INFORMATION



The parts MUST be replaced during the CVT main ball bearing replacement repair:



2002-2006 Mini Cooper (R50) L4-1.6L (W10) Page 268



The parts are to be removed and then re-used during the CVT main ball bearing replacement, and should be replaced ONLY if found to be defective



during visual inspection:



WARRANTY INFORMATION



Covered under the terms of the MINI New Vehicle Limited Warranty.

Friday, 4 May 2018

******** Audi A6 Quattro Sedan (4F2) V6-3.0L SC (CCAA) Technical DIAGNOSIS AND REPAIR # 391003 Date: 100629


A/T, Drivetrain - Vibrations On Tight Turns



37 Vibrations on tight turns



39 10 03



2022896/1



June 29, 2010



Affected Vehicles



Condition



Customer may report vibrations, humming noises or rubbing noises from the drivetrain when driving slowly around very tight turns. The noise is



particularly noticeable when maneuvering at full steering wheel lock in a parking lot.



Technical Background



Friction-reducing additives in the differential oil are reduced by wear. At high load on tight turns, the friction discs and worm wheel teeth in the



406



center differential are subject to wear.



This changes the friction and locking values in the center differential and causes vibrations in the drivetrain.



Production Solution



Service



Test drive the vehicle.



^ Light vibrations at full steering wheel lock are normal.



^ With stronger than normal vibrations in minor corners or heavy vibration at full steering wheel lock, proceed as follows:



a. Check the center differential according to the repair manual for correct oil level and inspect for damage (metal shavings).



b. Ensure the wheels are not damaged (bent) and all four tires are the correct size and the same type of tire.



c. If nothing is found, change the oil of the center differential with G 055 145 A2.



The center differential does not have a drain plug, therefore the gear oil can be drained only by removing the cover.



Follow the repair manual directions for removal and installation of the Self-Locking Center Differential Cover but only remove the cover far



enough to drain the oil. Then reassemble and fill with the new G 055 145 A2 oil.



d. Drive the vehicle along a lot of bends until the gearbox temperature reaches 80锟斤拷C and reassess the vibrations.



- If the vibrations have been reduced to normal, the concern is repaired.



- If the oil change does not repair the concern, submit a Technical Assistance Center ticket under the Concern Type: Audi Automatic



Transmission.



Warranty



Required Parts and Tools



Additional Information



All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service



manuals for the latest information.