AUDI Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.
Monday, 23 March 2020
Wednesday, 26 February 2020
手册最新信息。******** 奥迪A4Quattro车(8K5)L4-2.0L Turbo(CAEB)技术服务公 告#1151123日期:110705
369
活动LNVW-发动机凸轮轴调节置换
更新凸轮轴调整(LNVW)
15 23 11
2026802/1
七月5日,2011年
受影响的车辆
条件
这RVU已经主动发布以防止下列条件发生在车辆:
2.0T机凸轮轴调节更替。
这种车辆所需的更新(RVU)是在生效,直到除去。
车辆必须满足以下标准:^程序只适用于车辆,显示15D6码在ElsaWeb运动/行动的信息屏幕上每天的维修。
^车辆必须在有限的新车辆的保证。
^程序必须执行在规定的时间框架表示在这个技术服务公告。
^程序上都必须执行适用的车辆经销商的库存之前销售。
技术背景
奥迪车辆2.0L发动机内建立一个特定的时期,很可能不回阀在凸轮调整(承马鞍)可能中断。 因此,碎片的非返回阀门可以进入润滑系统。
生产方案
不适用的。
370
371
担保
所需要的零件和工具
^正确地销毁和处置的去除部分根据所有国家和地方的要求,除非另有说明和/或要求
通过的传奇故事。
^如果你有用尽分配的部分,你需要额外的零部件用于车辆受到这RVU但已经超过了你上了
限,请将您的请求增加的部分通过电子邮件。^确保包括受影响的葡萄酒与您的订单。 之前提交请求,确保每个车辆的15D6码打开
ElsaWeb的。 你便会进行审查,并相应地进行处理。
额外信息
以下技术服务公报(s)可能有必要完成这个过程:
372
^TSB2023107,01MIL上,噪音从时间链(DTC P001600)
所有零件和服务提供参考文献在这个RVU的情况下更改和/或清除。 总检查你的部门和服务
手册最新信息。
服务
服务^请通知客户已经采取了一个受影响的车辆时的车旁边,在讲习班。
^请确保所有受影响的车辆进行检查和修理期间的下一个服务访问。 请注意所需的活动
研讨会以前签署的客户。
^如果省略执行工作所需要的活动期间的讲习班的访问,通知客户有关的活动立即
(注册子邮件与咨询意见的receipt)。^传递的信息,你的新的和使用汽车的销售部门,使车辆受到影响的检查,如有必要,修复
立即的。
纵向发动机:
1. 拉开引擎盖板(图1,箭头)。
2. 分离接从凸阀控制(图2,1人)。
3. 删除螺栓(4)(图2,箭头)和分离凸轮轴控制阀。
373
提示:捕逃避石油与布。
4. 删除线束时链盖(图3)。
5. 拧螺栓为了(图4,1至5)(并删除时链盖。
注:
控制阀门有一个左手线。
3746. 拧开的控制阀的方向箭头(右)采用组装工具T10352的。
提示:捕逃避石油与布。
7. 删除螺栓。 (7)
8. 地布下支架(承鞍)抓住逃避石油和任何部分不回阀可能辍学。
375
注:
如果凸轮轴被损坏,按照该程序的详细TSB2023107的。
9. 替换架(承鞍).
Tip:润滑承表面与油之前安装的。
安装是在相反的顺序;注意如下:
1. 替换1和重新安装2和3:
紧扭矩:(图9,1)20纳米+90��(M8)更换的螺栓
(图9,2)35纳米-控制阀(左线!)
(图9,3)9纳米的螺栓
2. 重新密封和0-环仅如果损坏。 润滑用机油之前安装的。
376
拧螺栓在序列的图示。 (10图,1到5)。
紧扭矩:9Nm
重新连接线束。
3. 重新安装的螺栓。
紧扭矩:9Nm
连接凸轮轴控制阀门(图11,1)N205的。
Thursday, 14 March 2019
******** Audi A4 Quattro Wagon (8K5) L4-2.0L Turbo (CAEB) Technical DIAGNOSIS AND REPAIR # 1151123 Date: 110705
369
Campaign LNVW - Engine Camshaft Adjuster Replacement
UPDATE - Camshaft Adjuster (LNVW)
15 11 23
2026802/1
July 5, 2011
Affected Vehicles
Condition
This RVU has been proactively released to prevent the following condition from occurring in the vehicle:
2.0 T Engine camshaft adjuster replacement.
This Required Vehicle Update (RVU) is in effect until removed.
Vehicle must meet all of the following criteria:
^ Procedure is valid only for vehicles that show the 15D6 code in the ElsaWeb Campaign/Action Information screen on the day of repair.
^ Vehicle must be within the Limited New Vehicle Warranty.
^ Procedure must be performed within the allotted time frame stated in this Technical DIAGNOSIS AND REPAIR.
^ Procedure must be performed on applicable vehicles in dealer inventory prior to sale.
Technical Background
On Audi vehicles with 2.0L TFSI engines built within a specific period, it is possible that the non-return valve on the camshaft adjuster (bearing
saddle) may break. As a result, fragments of the non-return valve can enter the lubrication system.
Production Solution
Not applicable.
370
371
Warranty
Required Parts and Tools
^ Properly destroy and dispose of removed parts in accordance with all state and local requirements, unless otherwise indicated and/or requested
through SAGA.
^ If you have exhausted your allocated parts and you require additional parts for vehicles affected by this RVU but have exceeded your Upper Order
Limit, please submit your requests for additional parts via email.
^ Be sure to include the affected VINs with your order. Prior to submitting your request, ensure that each vehicle has the 15D6 code open in
ElsaWeb. Your order will be reviewed and processed accordingly.
Additional Information
The following Technical DIAGNOSIS AND REPAIR(s) may be necessary to complete this procedure:
372
^ TSB 2023107, 01 MIL on, noise from timing chain (DTC P001600)
All parts and service references provided in this RVU are subject to change and/or removal. Always check with your Parts Department and service
manuals for the latest information.
Service
Service
^ Please notify customers who have taken delivery of one of the affected vehicles when the vehicles are next in the workshop.
^ Please ensure that all affected vehicles are checked and repaired during the next service visit. Make a note of the required campaign on the
workshop order before it is signed by the customer.
^ If it is omitted to perform the work required for the campaign during a workshop visit, notify the customer about the campaign immediately
(registered mail with advice of receipt).
^ Pass on the information to your new and used car sales departments so that the vehicles affected are checked and, if necessary, repaired
immediately.
Longitudinal engine:
1. Pull off engine cover panel (Figure 1, arrows).
2. Detach connector from camshaft control valve (Figure 2, 1).
3. Remove bolts (4 total) (Figure 2, arrows) and detach camshaft control valve.
373
Tip: Catch escaping oil with a cloth.
4. Remove wire harness from timing chain cover (Figure 3).
5. Unscrew bolts in order (Figure 4, 1-5) ( and remove timing chain cover.
Note:
The control valve has a left-hand thread.
374
6. Unscrew control valve in direction indicated by arrow (clockwise) using assembly tool T10352.
Tip: Catch escaping oil with a cloth.
7. Remove bolts. (7 total)
8. Place cloth under bracket (bearing saddle) to catch escaping oil and any parts of non-return valve that may drop out.
375
Note:
If the camshaft is damaged, follow the procedure detailed in TSB 2023107.
9. Replace bracket (bearing saddle).
Tip: Lubricate bearing surface with oil before installing.
Installation is carried out in the reverse order; note the following:
1. Replace 1 and reinstall 2 and 3:
Tightening torques:
(Figure 9, 1) 20 Nm + 90锟斤拷 (M8) - Replace bolt
(Figure 9, 2) 35 Nm - Control valve (Left-hand thread!)
(Figure 9, 3) 9 Nm - Bolt
2. Renew seal and 0-ring only if damaged. Lubricate with engine oil before installing.
376
Tighten bolts in the sequence shown. (Figure 10, 1 to 5).
Tightening torque: 9 Nm
Reconnect wire harness.
3. Reinstall bolts.
Tightening torque: 9 Nm
Connect camshaft control valve (Figure 11, 1) N205.
Saturday, 9 March 2019
マニュアルの最新情報です。******** Audi A4クワトロワゴン(8K5)L4-2.0Lター ボ(CAEB)技術サービス紀#1151123日:110705
369
キャンペーンLNVW-エンジンのカムシャフトをアジャスター交換
更新-カムシャフトをアジャスター(LNVW)
15 11 23
2026802/1
月5,2011
影響を受け車両
条件
このRVUに積極的に取り組んでおり、発防止の状態から発生する車両:
2.0Tエンジンのカムシャフトをアジャスターに交換できます。
この要求を更新(RVU)まで有効で削除されます。
車両はすべて満たすのは、以下の基準を^手続きのみ有効とした自動車ショーに15D6コードのElsaWebキャンペーン/アクション情報画面の補修します。
^車内でなければならな限り新しい車両保証が付いています。
^手順を実施することが必要である競合他社の峻別、収集時間フレームに記この技術サービスについて
^手順を実施することが必要であるに対して適用車ディーラー在庫の前に販売いたします。
技術的背景
上のAudi車2.0L TFSIエンジン内に建設した特定の期間では逆止め弁のカムシャフトをアジャスター(ベアリングサドル部分が破断することになります。 その結果、片を逆止め弁の潤滑システムです。
制作のトータルソリューション
該当ありません。
370
371
保証
必要な部品やツール
^管理責任のもとで適切に破棄-処分の除去された部品に従ってすべての国及び地域要件には、特別の断りがない限り、および/またはお申し込みいただいた
を通じて設定をお願いします。
^だくご割り当ての部品が必要部品を自動車の影響を受けてRVUが上になってい上順
制限、提出してください請求のための追加パーツをメールにて差し上げます。^くださいなどの影響を受けVINsと。 提出前の申し出により、確実にそれぞれの車両の15D6コードを開
ElsaWebます。 ご注文の見直しおよび加工処理されます。
追加情報
以下の技術サービス研究紀要(s)が必要な手続き:
372
^TSB2023107,01百万円には、ノイズからタイミングチェーン(DTC P001600)
すべての部品およびサービスを参照のこRVUしに変更又は削除します。 必ず確認してくださいお部品部門、サービス
マニュアルの最新情報です。
サービス
サービス^くださいお客さまにお知らせいただいた配送の影響を受け時の車両の車両は次のワークショップである。
^してください影響を受けたすべての車検や修理時に次のサービスです。 また、キャンペーンの
ワ順で前ではないかといわれている。
^省略した場合は、必要な作業のためのキャンペーンションの訪問を通知につきましては、お客様のキャンペーンを直ちに
(登録メールアドバイスを受領します。^にお客さまからのお問い合わせ内容"新車-中古車販売部門では、車両の影響などを確認し、必要な場合は、修理
すぐです。
縦置きエンジン:
1. カップリンエンジンカバーパネル(図1、矢印)です。
2. 取り外しコネクタからカムシャフト制御バルブ(図2は、1)です。
3. 削除ボルト(4)(図2、矢印)の取り外しカムシャフト制御弁です。
373
ヒント:チ逃げ油をする。
4. 除ワイヤーハーネスからタイミングチェーンカバー(Figure3)。
5ます。 を逆にボルトを図4,1-5)(および削除のタイミングチェーンをカバーします。
注意:
の制御バルブは、左ねじになります。
3746ます。 はずの制御バルブの方向を示す矢印(時計回りに回)を組み立て工作T10352ます。
ヒント:チ逃げ油をする。
7. 削除ボルトです。 (7合計)
8. 場所を布の下でブラケット(サドル)の追脱石油や部品の不返バルブが落ちます。
375
注意:
場合にはカムシャフトが破損しているときは、手続きの詳細にTSB2023107ます。
9. ブラケット交換(サドル)です。
ヒント:潤滑軸受の表面に油をインストールする前にします。
据付を行うには、次の点に注意してください:
1. 置き換え1は、再インストール2,3:
締め付けトルク:(図9では、1)20Nm+90話(M8)-ボルト交換
(図9に、2)35ナノメートルのコントロールバルブで調節します(左側のスレッドです!)
(図9に、3)9Nm-ボルト
2. 更新印鑑-0-リングが破損します。 を付けるとエンジンオイルをインストールする前にします。
376
締め付けボルトの列を表示します。 (図10、1~5ます。
締め付けトルク:9Nm
再接続ワイヤーハーネスです。
3. 再インストールボルトです。
締め付けトルク:9Nm
接続カムシャフト制御バルブ(図11は、1)N205ます。