Body - Windows Knock/Click/Squeak When Operated
64 Window regulator noisy during operation
64 11 12
2022450/4
February 10, 2011.
Supersedes Technical DIAGNOSIS AND REPAIR Group 64 number 10 - 11 dated December 6, 2010 for reasons listed below.
376
AFFECTED VEHICLES
CONDITION
During window regulator operation, various noises are heard by the customer. The noise could be a knock, click squeak, etc.
TECHNICAL BACKGROUND
Conflicting tolerances in the window regulator mechanism.
PRODUCTION SOLUTION
New supplier for window regulator mechanism.
Update the door control unit via SVM
1. Follow all instructions in the attached TSB 2011732 00 Software Version Management (SVM), operating instructions.
2. Update the door control unit using the SVM action code as necessary.
Driver's door: XCHG42A001
Passenger's door: XCHG52A001
3. Check operation of both window regulators.
4. Send feedback to update the SVM database.
377
WARRANTY INFORMATION
REQUIRED PARTS AND TOOLS
ADDITIONAL INFORMATION
The following Technical DIAGNOSIS AND REPAIR(s) will be necessary to complete this procedure:
^ 2011732 00 Software Version Management (SVM), operating instructions
All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service
manuals for the latest information.
ATTACHMENTS
378
379
380
381
382
383
384
2011732 00 Software Version Management (SVM), operating instructions
Service Procedure
SERVICE
Tip: Replace only the affected window regulator; it is not necessary to replace both window regulators.
Determine whether the new repair kit is necessary
385
Before ordering the repair set, use a VAS diagnostic tester to determine the part number of the door control unit.
^ If the part number is 8T0 959 793 J (or higher index) for the drivers side or 8T0 959 792 J (or higher index) for the passengers side, the entire
repair set is not necessary. Only a new window regulator is necessary.
^ If the part number of the door control unit is 8K0 959 792, 8K0 959 793, 8K0 959 792 H or 8K0 959 793 H, order the complete repair set
(comprised of a new window regulator mechanism, door control unit and outer door seal).
Complete modifications necessary to install the new repair set
1. The attachment of the Bowden cables to the door shell has changed. Originally the upper cable was secured to the door shell using a double clip
(see Figure 2) mounted to the inside of the door shell.
386
Remove the clip.
2. The upper cable on the replacement window regulator has a clip that will be inserted into the hole labeled "A" Figure 4.
If hole "A" is not present in the door shell, use the upper hole labeled "J" in Figure 4.
Note which hole you will use.
3. The improved window regulator is fitted with a second clip on the lower cable that must be attached to the door shell. It will attach to a hole near
the lateral acceleration sensor. This hole has been in the door shell since mid-2008 production.
Determine if the hole is present. If this hole is not present, the hole must be drilled.
387
a. Remove the side airbag crash sensor in the door to establish the position of the hole.
b. Using the edges of the opening for the side airbag crash sensor as a guide, draw perpendicular lines as shown in Figure 6.
A: 18mm
B: 27mm
Hole diameter: 6.5mm
c. Drill and deburr the hole.
d. Apply Anti-Corrosion Wash Primer ALN 002 003 10 with a brush and allow to thoroughly dry.
e. Treat the surface with Anti Corrosion Wax D 308 SP5 A1.
388
Note:
Use caution not to allow any wax to come in contact with the lateral acceleration sensor.
f. Close the hole used by the original window regulator with Bung N 909 826 01.
Install the entire repair set
^ Make sure to install all components of the repair set.
Tip: Door control units with indexes below "J" installed with the improved window regulator will malfunction.
^ An additional bolt WHT 004 905 will be required. This bolt is not included in the repair set. One bolt per door is required.
^ In some cases the door seal provided in the repair set may need to be modified slightly.
Depending on the VIN of the vehicle, there are two possible door profiles.
389
The replacement seal may have a notch that will need to be cut to accommodate the door profile shown in Figure 8.
