Audi Q7 Quattro Technical 260905 Date: 091103
Engine Controls - MIL ON/Glow Plug Lamp ON/DTC P2002
26 Implausible signal of differential pressure sensor (DTC P2002)
26 09 05
2021419/2
November 3, 2009.
Supersedes Technical Service Bulletin Group 26 number 09-04 dated September 9, 2009 for reasons listed below.
Affected Vehicles
Condition
^ MIL on.
^ Glow plug light illuminated.
^ Particle filter symbol displayed in instrument cluster.
^ Engine goes into limp mode.
^ DTC P2002 for diesel particulate filter malfunction is stored in the ECM data memory.
Technical Background
The two 0.35 mm?wires (pin 2, grey/white; and pin 3, red/grey) on the connector to the differential pressure sensor have excess contact resistance.
Production Solution
Audi Q7 Quattro 249
Change to enlarged (0.5 mm? wires with gold-plated contacts.
Service
1. Remove plastic connector from differential pressure sensor.
2. Remove connector skirt from connector.
3. Remove connector lock.
4. Remove pin 3 from the connector.
5. Cut wire from pin 3 approximately 60 mm from the plastic connector.
6. Replace the 0.35 mm?wire with a 0.5 mm?wire with a gold-plated connector using a seal and butt connector.
7. Install wire, pin, and seal into plastic connector using the tools included in the VAS 1978 kit.
8. Repeat steps 4-7 for pin 2, cutting wire approximately 85 mm from the connector.
9. Reinstall connector lock.
10. Reinstall wire sheath.
11. Reinstall connector skirt and plug plastic connector into DPF pressure sensor.
Audi Q7 Quattro 250
Warranty
Required Parts and Tools
Additional Information
All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service
manuals for the latest information.
Engine Controls - MIL ON/Glow Plug Lamp ON/DTC P2002
26 Implausible signal of differential pressure sensor (DTC P2002)
26 09 05
2021419/2
November 3, 2009.
Supersedes Technical Service Bulletin Group 26 number 09-04 dated September 9, 2009 for reasons listed below.
Affected Vehicles
Condition
^ MIL on.
^ Glow plug light illuminated.
^ Particle filter symbol displayed in instrument cluster.
^ Engine goes into limp mode.
^ DTC P2002 for diesel particulate filter malfunction is stored in the ECM data memory.
Technical Background
The two 0.35 mm?wires (pin 2, grey/white; and pin 3, red/grey) on the connector to the differential pressure sensor have excess contact resistance.
Production Solution
Audi Q7 Quattro 249
Change to enlarged (0.5 mm? wires with gold-plated contacts.
Service
1. Remove plastic connector from differential pressure sensor.
2. Remove connector skirt from connector.
3. Remove connector lock.
4. Remove pin 3 from the connector.
5. Cut wire from pin 3 approximately 60 mm from the plastic connector.
6. Replace the 0.35 mm?wire with a 0.5 mm?wire with a gold-plated connector using a seal and butt connector.
7. Install wire, pin, and seal into plastic connector using the tools included in the VAS 1978 kit.
8. Repeat steps 4-7 for pin 2, cutting wire approximately 85 mm from the connector.
9. Reinstall connector lock.
10. Reinstall wire sheath.
11. Reinstall connector skirt and plug plastic connector into DPF pressure sensor.
Audi Q7 Quattro 250
Warranty
Required Parts and Tools
Additional Information
All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service
manuals for the latest information.
