Audi Q7 Quattro Technical 271210 Date: 120213
Battery - Testing/Charging On BDM Equipped Vehicles
27 Battery testing and charging - vehicles with BDM (J367)
27 12 10
2023282/2
February 13, 2012.
Supersedes Technical Service Bulletin Group 27 number 10 - 05 dated May 5, 2010 for reasons listed below.
Affected Vehicles
Audi Q7 Quattro 166
Condition
Battery testing and charging for vehicles equipped with a Battery Data Manager (BDM - J367).
Technical Background
When the Incharge 940 is used as a battery charger in auto mode, it performs a battery condition test and may prematurely fail the battery if the
charging takes place at the jumper posts in the engine compartment. This is due to the added resistance in the system between the battery and jumper
posts. When the Incharge 940 is used as a battery charger in manual mode, the battery condition test is not performed.
Production Solution
Not applicable.
Service
TESTING THE BATTERY
VAS scan tool:
Follow Guided Fault Finding battery test plan in service work.
CHARGING THE BATTERY
Midtronics INC-940 diagnostic charging station:
Connect the charging station - auto mode
1. Connect the Incharge 940 positive cable clamp to the positive battery post.
Audi Q7 Quattro 167
2. Connect the negative cable clamp to the vehicles negative battery cable downstream at the body attachment point. (Figures 1 and 2 illustrate this
on an Audi Q5.)
Tip: This connection ensures J367 remains in the loop so that it may provide battery charge data to the Gateway (J533) as the J367 is clamped
directly to the battery negative post.
3. Enter the DIN value listed on the battery.
Connect the charging station - manual mode
1. Connect the Incharge 940 to the battery jumping posts in the engine compartment or as described in the auto mode section.
2. Enter the DIN value listed on the battery.
Tip: Please obtain the battery serial number (example: VAO 99050770MX), located on top of the battery, for battery testing or replacement and for
future reference or when contacting the Technical Assistance Center (TAC).
Warranty
This TSB is informational only and not applicable to any Audi warranty.
Additional Information
All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service
manuals for the latest information.
Battery - Testing/Charging On BDM Equipped Vehicles
27 Battery testing and charging - vehicles with BDM (J367)
27 12 10
2023282/2
February 13, 2012.
Supersedes Technical Service Bulletin Group 27 number 10 - 05 dated May 5, 2010 for reasons listed below.
Affected Vehicles
Audi Q7 Quattro 166
Condition
Battery testing and charging for vehicles equipped with a Battery Data Manager (BDM - J367).
Technical Background
When the Incharge 940 is used as a battery charger in auto mode, it performs a battery condition test and may prematurely fail the battery if the
charging takes place at the jumper posts in the engine compartment. This is due to the added resistance in the system between the battery and jumper
posts. When the Incharge 940 is used as a battery charger in manual mode, the battery condition test is not performed.
Production Solution
Not applicable.
Service
TESTING THE BATTERY
VAS scan tool:
Follow Guided Fault Finding battery test plan in service work.
CHARGING THE BATTERY
Midtronics INC-940 diagnostic charging station:
Connect the charging station - auto mode
1. Connect the Incharge 940 positive cable clamp to the positive battery post.
Audi Q7 Quattro 167
2. Connect the negative cable clamp to the vehicles negative battery cable downstream at the body attachment point. (Figures 1 and 2 illustrate this
on an Audi Q5.)
Tip: This connection ensures J367 remains in the loop so that it may provide battery charge data to the Gateway (J533) as the J367 is clamped
directly to the battery negative post.
3. Enter the DIN value listed on the battery.
Connect the charging station - manual mode
1. Connect the Incharge 940 to the battery jumping posts in the engine compartment or as described in the auto mode section.
2. Enter the DIN value listed on the battery.
Tip: Please obtain the battery serial number (example: VAO 99050770MX), located on top of the battery, for battery testing or replacement and for
future reference or when contacting the Technical Assistance Center (TAC).
Warranty
This TSB is informational only and not applicable to any Audi warranty.
Additional Information
All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service
manuals for the latest information.
